Keithley 2450 - Page 857

Appendix
D: Model 2450 in a Model 2400 application Model 2450 Interactive SourceMeter® Instrument
Reference Manual
D-14 2450-901-01 Rev. B/September 2013
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe:AUTO
[:SENSe[1]]:CURRent[:DC]:RANGe:AUTO?
[:SENSe[1]]:RESistance:RANGe:AUTO
[:SENSe[1]]:RESistance:RANGe:AUTO?
[:SENSe[1]]:VOLTage[:DC]:RANGe:AUTO
[:SENSe[1]]:VOLTage[:DC]:RANGe:AUTO?
Model 2450 command
[:SENSe[1]]:<function>:RANGe:AUTO (on page 6-50
), where <function> is
VOLTage[:DC], CURRent[:DC], or RESistance.
[:SENSe[1]]:<function>:RANGe:AUTO?
Notes
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe:AUTO:LLIMit
[:SENSe[1]]:CURRent[:DC]:RANGe:AUTO:LLIMit?
[:SENSe[1]]:RESistance:RANGe:AUTO:LLIMit
[:SENSe[1]]:RESistance:RANGe:AUTO:LLIMit?
[:SENSe[1]]:VOLTage[:DC]:RANGe:AUTO:LLIMit
[:SENSe[1]]:VOLTage[:DC]:RANGe:AUTO:LLIMit?
Model 2450 command
[:SENSe[1]]:<function>:RANGe:AUTO:LLIMit (on page 6-51), where
<function> is VOLTage[:DC], CURRent[:DC], or RESistance.
[:SENSe[1]]:<function>:RANGe:AUTO:LLIMit?
Notes
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe:AUTO:ULIMit?
[:SENSe[1]]:RESistance:RANGe:AUTO:ULIMit
[:SENSe[1]]:RESistance:RANGe:AUTO:ULIMit?
[:SENSe[1]]:VOLTage[:DC]:RANGe:AUTO:ULIMit?
Model 2450 command
[:SENSe[1]]:<function>:RANGe:AUTO:ULIMit (on page 6-52), where
<function>
is
VOLTage[:DC]
or
RESistance
.
Notes
Upper limit is not available for current for Model 2450. For voltage, you can
query the upper limit for voltage, but not set it.
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe:HOLDoff
[:SENSe[1]]:CURRent[:DC]:RANGe:HOLDoff?
Model 2450 command
Not available
Notes
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe:HOLDoff:DELay
[:SENSe[1]]:CURRent[:DC]:RANGe:HOLDoff:DELay?
Model 2450 command
Not available
Notes
Model 2400 command
[:SENSe[1]]:CURRent[:DC]:RANGe[:UPPer]
[:SENSe[1]]:CURRent[:DC]:RANGe[:UPPer]?
[:SENSe[1]]:RESistance:RANGe[:UPPer]
[:SENSe[1]]:RESistance:RANGe[:UPPer]?
[:SENSe[1]]:VOLTage[:DC]:RANGe[:UPPer]
[:SENSe[1]]:VOLTage[:DC]:RANGe[:UPPer]?
Model 2450 command
[:SENSe[1]]:<function>:RANGe[:UPPer] (on page 6-53), where <function> is
VOLTage[:DC], CURRent[:DC], or RESistance.
[:SENSe[1]]:<function>:RANGe[:UPPer]?
Notes