Keithley 2450 - Page 864

Model 2450
Interactive SourceMeter® Instrument Reference Manual Appendix D:
Model 2450 in a Model 2400 application
2450-901-01 Rev. B/September 2013 D-21
Model 2400 command
:SOURce[1]:SWEep:CABort
:SOURce[1]:SWEep:CABort?
Model 2450 command
:SOURce[1]:SWEep:<function>:LINear (on page 6-81)
:SOURce[1]:SWEep:<function>:LINear:STEP (on page 6-83)
:SOURce[1]:SWEep:<function>:LIST (on page 6-85)
:SOURce[1]:SWEep:<function>:LOG (on page 6-87)
Notes
Sweep parameters are built into the sweep command path. See Sweep
operation (on page 3-51) for information.
Model 2400 command
:SOURce[1]:SWEep:DIRection
:SOURce[1]:SWEep:DIRection?
Model 2450 command
:SOURce[1]:SWEep:<function>:LINear (on page 6-81)
:SOURce[1]:SWEep:<function>:LINear:STEP (on page 6-83)
:SOURce[1]:SWEep:<function>:LIST (on page 6-85)
:SOURce[1]:SWEep:<function>:LOG (on page 6-87)
Notes
Sweep parameters are built into the sweep command path. See Sweep
operation (on page 3-51) for information.
Model 2400 command
:SOURce[1]:SWEep:POINts
:SOURce[1]:SWEep:POINts?
Model 2450 command
Use the sweep commands to define sweeps:
:SOURce[1]:SWEep:<function>:LINear (on page 6-81)
:SOURce[1]:SWEep:<function>:LINear:STEP (on page 6-83)
:SOURce[1]:SWEep:<function>:LIST (on page 6-85)
:SOURce[1]:SWEep:<function>:LOG (on page 6-87)
Notes
Sweep parameters are built into the sweep command path. See Sweep
operation (on page 3-51) for information.
Model 2400 command
:SOURce[1]:SWEep:RANGing
:SOURce[1]:SWEep:RANGing?
Model 2450 command
:SOURce[1]:SWEep:<function>:LINear (on page 6-81)
:SOURce[1]:SWEep:<function>:LINear:STEP (on page 6-83)
:SOURce[1]:SWEep:<function>:LIST (on page 6-85)
:SOURce[1]:SWEep:<function>:LOG (on page 6-87)
Notes
Sweep parameters are built into the sweep command path. See Sweep
operation (on page 3-51) for information.
Model 2400 command
:SOURce[1]:SWEep:SPACing
:SOURce[1]:SWEep:SPACing?
Model 2450 command
:SOURce[1]:SWEep:<function>:LINear (on page 6-81)
:SOURce[1]:SWEep:<function>:LINear:STEP (on page 6-83)
:SOURce[1]:SWEep:<function>:LIST (on page 6-85)
:SOURce[1]:SWEep:<function>:LOG (on page 6-87)
Notes
Sweep parameters are built into the sweep command path. See Sweep
operation (on page 3-51) for information.
Model 2400 command
:SOURce[1]:VOLTage:PROTection[:LEVel]
:SOURce[1]:VOLTage:PROTection[:LIMit]?
Model 2450 command
:SOURce[1]:<function>:PROTection[:LEVel] (on page 6-73)
Notes
Model 2400 command
:SOURce[1]:VOLTage:PROTection[:LEVEL]:TRIPped?
Model 2450 command
:SOURce[1]:<function>:PROTection[:LEVEL]:TRIPped? (on page 6-74)
Notes