Kikusui TOS9301 - Page 9

TOS93 Series User’s Manual 9
Test time............................................................. 144
Measurement range ........................................... 145
Measurement mode (Measure Mode) ................ 147
Voltmeter band expansion (V
olt
Meter BandWidth) ..
148
Peak value display (Display P
eak
hold) .............. 149
Measurement check (Measure Check)............... 149
Offset .................................................................. 150
Voltage conversion (Conv V
olt
age) .................... 151
Checking the EUT
operation (Line OUT)............ 151
Starting a Test ................................................152
Connecting the test leads to the EUT................. 152
Starting a test ..................................................... 154
Operation after a test starts ................................ 155
Finishing the Test and Viewing the Judgment157
Stopping tests..................................................... 157
Conditions that cause a test to end .................... 157
Judgment types and operation ........................... 158
Clearing the judgment result............................... 158
Protective Conductor
Current Test
Setting Test Conditions ..................................159
Displaying the setup screen (Home menu) ........ 159
Description of test conditions.............................. 160
Network .............................................................. 161
Polarity of the power supply line......................... 162
Single fault mode (Condition) ............................. 162
Upper limit .......................................................... 163
Lower limit .......................................................... 164
Judgment delay (Judge Delay)........................... 165
Test time............................................................. 166
Measurement range ........................................... 167
Measurement mode (Measure Mode) ................ 168
Voltmeter band expansion (V
olt
Meter BandWidth) ..
169
Peak value display (Display P
eak
hold) .............. 170
Measurement check (Measure Check)............... 170
Offset .................................................................. 171
Voltage conversion (Conv V
olt
age) .................... 172
Checking the EUT
operation (Line OUT)............ 172
Starting a Test ................................................173
Starting a test ..................................................... 173
Operation after a test starts ................................ 174
Finishing the Test and Viewing the Judgment176
Stopping tests..................................................... 176
Conditions that cause a test to end .................... 176
Judgment types and operation ........................... 177
Clearing the judgment result............................... 177
Patient Leakage Current
Test
Setting Test Conditions ..................................178
Displaying the setup screen (Home menu) ........ 178
Description of test conditions ............................. 179
Network .............................................................. 179
Polarity of the power supply line......................... 180
Single fault mode (Condition)............................. 181
Probe connection destination............................. 182
Output from the 110% terminal (110% OUT) ..... 183
Upper limit .......................................................... 184
Lower limit .......................................................... 185
Judgment delay (Judge Delay)........................... 186
Test time............................................................. 187
Measurement range ........................................... 188
Measurement mode (Measure Mode)................ 189
Voltmeter band expansion (V
olt
Meter BandWidth) ..
190
Peak value display (Display P
eak
hold) .............. 191
Measurement check (Measure Check) .............. 191
Offset.................................................................. 192
Voltage conversion (Conv V
olt
age).................... 193
Checking the EUT
operation (Line OUT) ........... 193
Starting a Test................................................194
Connecting the test leads to the EUT................. 194
Starting a test ..................................................... 196
Operation after a test starts................................ 197
Finishing the Test and Viewing the Judgment199
Stopping tests..................................................... 199
Conditions that cause a test to end.................... 199
Judgment types and operation........................... 200
Clearing the judgment result .............................. 200
Meter Mode
Constructing the Measurement Circuit...........202
Setting Measurement Conditions ...................203
Displaying the setup screen (Home menu) ........ 203
Overview of measurement conditions ................ 203
Network .............................................................. 204
Measuring across terminals A
an
d B (A-B Terminal)
205
SELV
setting...
.................................................... 206
Measurement range ........................................... 207
Measurement mode (Measure Mode)................ 208
Measurement check (Measure Check) .............. 208
Offset.................................................................. 209
Output from the 110% terminal (110% OUT) ..... 210
Polarity of the 110% output ................................ 211
Executing a Measurement .............................212