Combination mode
186
DKit Setting is checked. In conjunction with this, the
Drum Kit IFX Patch setting will be reset to the default
setting.
• If IFXs is checked, the Bus Select setting of the copy-
source program will be copied. If the copy-destination
timbre Bus Select was set to IFX1–IFX5, it will
automatically be set to L/R. If you check IFX-All used,
the routing will be automatically set to match the copy-
source program.
• If IFXs used is unchecked, then the copy-source Bus
Select setting will be ignored. or if the Bus Select of the
copy-source program and copy-destination timbre is set
to IFX1–IFX5, it will automatically be set to L/R.
4. If you check “with KARMA,” the Program’s KARMA
settings will also be copied.
If this is On (checked), the KARMA Module settings of the
copy-source program will be copied to the “KARMA
Module” you specify in step 8. The Set Up Pads settings will
be also be copied.
In Combination mode, the KARMA Module’s In (Input
Channel) will be set to Gch, its Out (Output Channel) will
be set to the MIDI channel of the timbre you specify in step
5, and Track Thru will be turned On (checked).
5. If you check “with Drum Track,” the Drum Track Pat-
tern settings of the copy-source program will also be
copied.
If this is On (checked), the Drum Track Pattern settings of
the copy-source program will be copied to the “Drum
Track” you specify in step 9.
The MIDI channel specified for the Drum Track copy-
destination timbre will be used.
6. If you check RADIAS Vocoder, the RADIAS Vocoder
parameters of the copy-source RADIAS program will
also be copied.
The EXB-RADIAS must be installed in order to select and
use a RADIAS program.
This is invalid if an EDS program is selected by the copy-
source.
7. Use the To field to specify the copy-destination timbre.
The parameters for each timbre will be initialized. The copy-
source program will be assigned to Program (see “0–1(2)b:
Program Select” on page 122).
• The MIDI Channel (Combi 3–1(2)c) setting will not
change if “KARMA” is checked. If “KARMA” is
unchecked, MIDI Channel will be automatically set to G
ch.
• The Bank Select (When Status=EX2) (Combi 3–1(2)c)
setting will not change.
• The Status (Combi 3–1(2)c) setting will automatically be
set to INT.
• The P1: DT/XY/Ctrls– Controllers Setup settings of the
copy-source program will be copied.
8. Use the “Module” field to select the copy-destination
KARMA Module; either A, B, C, or D.
9. Use Drum Track to specify the destination timbre to
which the drum track program will be copied.
10.Press the OK button to execute the copy. If you decide
not to execute, press the Cancel button.
Copy X–Y Motion
Here’s how you can copy the X–Y motion setting from any
program, combination, or song, or from Sampling mode.
For more information, please see “Copy X–Y Motion” on
page 107.
Metronome Setup
This specifies whether the metronome will sound a count-
down before sampling begins. This can be set only if Trigger
is set to Sampling START SW.
The Metronome Precount (Prog 0–7b) setting is used.
For more information, please see “Metronome Setup” on
page 107.
Optimize RAM
Optimize RAM is available on the Sampling/Audio In tab
of the Play page. This command reorganizes unused space
in RAM, allowing the full amount of remaining memory to
be used.
For more information, please see “Optimize RAM” on
page 107.
Select Bank & Smpl No.
Select Sample No. is available on the Sampling/Audio In
tab of the Play page.
This specifies the sample number into which the sampled
data will be written. You can also specify whether the
sample will automatically be converted to a program after
sampling. Select Sample No. can be selected if you have
selected RAM as the Save to destination.
For more information, please see “Select Bank & Sample
No.” on page 108.
Select Directory
Select Directory is available on the Sampling/Audio In tab
of the Play page, when the sampling Save to parameter is
set to MEDIA.
When sampling to media, this lets you set the media,
directory, and file name for the resulting timbres 2–8 and 9–
16WAVE file.
For more information, please see “Select Directory” on
page 108.
Auto Sampling Setup
Auto Sampling Setup is available on the Sampling/Audio
In tab of the Play page.
This command automatically sets sampling-related
parameters in Combination mode. This is a helpful
convenience when you’re resampling your performance on
a combination, or when you’re using a combination as a
guide while sampling an external source. You can also use
this command to initialize the settings.
• Initialize: Sets sampling-related parameters to their
default state.
To Next Page
Loading...
Need help?
General
