MacDon FlexDraper FD75 - Page 11

214323 ix Revision B
3.11.2 Installing Beater Bars ................................................................................................................ 112
3.12 Transporting Header ......................................................................................................................... 113
3.12.1 Transporting Header on Combine................................................................................................ 113
3.12.2 Towing Header ........................................................................................................................ 113
Attaching Header to Towing Vehicle ............................................................................................ 114
Precautions for Towing a Header................................................................................................. 114
3.12.3 Converting from Transport to Field Position .................................................................................. 115
Removing Tow-Bar.................................................................................................................... 115
Storing the Tow-Bar .................................................................................................................. 116
Moving Front Wheels into Field Position....................................................................................... 117
Moving Rear Wheels into Field Position ........................................................................................ 119
3.12.4 Converting from Field to Transport Position .................................................................................. 121
Moving Front Wheels into Transport Position ................................................................................ 121
Moving Rear Wheels into Transport Position ................................................................................. 123
Attaching Tow-Bar .................................................................................................................... 126
Chapter 4: Auto Header Height Control ................................................................................................ 129
4.1 Auto Header Height Control System Overview ......................................................................................... 129
4.2 Auto Header Height Control Sensor Operation......................................................................................... 131
4.3 Replacing Auto Header Height Control Sensor ......................................................................................... 132
4.4 Sensor Output Voltage Range – Combine Requirements............................................................................ 134
4.4.1 Manually Checking Voltage Range................................................................................................. 135
4.4.2 Adjusting Voltage Limits .............................................................................................................. 137
4.5 Case IH 2300/2500 and 5088/6088/7088 Combines.................................................................................. 139
4.5.1 Engaging Auto Header Height Control – Case IH 2300....................................................................... 139
4.5.2 Calibrating Auto Header Height Control – Case IH 2300/2500 and 5088/6088/7088............................... 140
4.5.3 Setting Sensitivity of Auto Header Height Control – Case IH 2300/2500 and 5088/6088/7088.................. 141
4.6 Case IH 5130/6130/7130 and 5140/6140/7140 Midrange Combines............................................................ 143
4.6.1 Setting up the Header on the Combine Display – Case IH 5130/6130/7130; 5140/6140/7140.................. 143
4.6.2 Checking Voltage Range from Combine Cab – Case IH 5130/6130/7130; 5140/6140/7140 ...................... 145
4.6.3 Calibrating Auto Header Height Control – Case IH 5130/6130/7130; 5140/6140/7140............................ 147
4.6.4 Setting Preset Cutting Height – Case IH 5130/6130/7130; 5140/6140/7140.......................................... 148
4.7 Case IH 7010/8010, 7120/8120/9120, 7230/8230/9230, and 7240/8240/9240 Combines................................ 151
4.7.1 Checking Voltage Range from Combine Cab – Case 8010 .................................................................. 151
4.7.2 Setting Header Controls – Case IH 8010 ......................................................................................... 153
4.7.3 Checking Voltage Range from Combine Cab – Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240........................................................................................................................ 154
4.7.4 Calibrating Auto Header Height Control – Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240 – Software Versions Below 28.00 .......................................................................... 157
4.7.5 Calibrating Auto Header Height Control – Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240 – Software Versions Above 28.00 .......................................................................... 159
4.7.6 Setting Preset Cutting Height – Case 7010/8010, 7120/8120/9120, 7230/8230/9230,
7240/8240/9240........................................................................................................................ 161
4.8 Challenger
®
Combines ......................................................................................................................... 163
4.8.1 Checking Voltage Range from Combine Cab – Challenger
®
6 and 7 Series ............................................. 163
4.8.2 Engaging Auto Header Height Control – Challenger
®
6 Series ............................................................. 165
TABLE OF CONTENTS