MacDon FlexDraper FD75 - Page 12

214323 x Revision B
4.8.3 Calibrating Auto Header Height Control – Challenger
®
6 Series ........................................................... 165
4.8.4 Adjusting Header Height – Challenger
®
6 Series ............................................................................... 167
4.8.5 Adjusting Header Raise/Lower Rate – Challenger
®
6 Series ................................................................ 168
4.8.6 Setting Sensitivity of Auto Header Height Control – Challenger
®
6 Series.............................................. 170
4.9 CLAAS 500 Series Combines.................................................................................................................. 171
4.9.1 Calibrating Auto Header Height Control – CLAAS 500 Series............................................................... 171
4.9.2 Setting Cutting Height – CLAAS 500 Series ...................................................................................... 173
4.9.3 Setting Preset Cutting Height – CLAAS 500 Series............................................................................. 173
4.9.4 Setting Cutting Height Manually – CLAAS 500 Series......................................................................... 174
4.9.5 Setting Sensitivity of Auto Header Height Control – CLAAS 500 Series ................................................. 175
4.9.6 Adjusting Auto Reel Speed – CLAAS 500 Series ................................................................................ 178
4.10 CLAAS 600 and 700 Series Combines .................................................................................................... 181
4.10.1 Calibrating Auto Header Height Control – CLAAS 600 and 700 Series ................................................. 181
4.10.2 Setting Cutting Height – CLAAS 600 and 700 Series......................................................................... 183
4.10.3 Setting Sensitivity of Auto Header Height Control – CLAAS 600 and 700 Series .................................... 184
4.10.4 Adjusting Auto Reel Speed – CLAAS 600 and 700 Series .................................................................. 186
4.11 Gleaner
®
R62/R72 Combines............................................................................................................... 188
4.11.1 System Requirements – Gleaner
®
R62/R72.................................................................................... 188
4.11.2 Calibrating Auto Header Height Control – Gleaner
®
R62/R72 ............................................................ 188
4.11.3 Setting Sensitivity of Auto Header Height Control – Gleaner
®
R62/R72 Series ...................................... 189
4.12 Gleaner
®
R65/R66/R75/R76 and S Series Combines – Except S9 Series ....................................................... 192
4.12.1 Checking Voltage Range from Combine Cab – Gleaner
®
R65/R66/R75/R76 and S Series ........................ 192
4.12.2 Engaging Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series ................................ 193
4.12.3 Calibrating Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series.............................. 195
4.12.4 Turning Accumulator Off – Gleaner
®
R65/R66/R75/R76 and S Series.................................................. 196
4.12.5 Adjusting Header Raise/Lower Rate – Gleaner
®
R65/R66/R75/R76 and S Series ................................... 196
4.12.6 Adjusting Ground Pressure – Gleaner
®
R65/R66/R75/R76 and S Series............................................... 197
4.12.7 Adjusting Sensitivity of Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series ............. 198
4.12.8 Troubleshooting Alarms and Diagnostic Faults – Gleaner
®
R65/R66/R75/R76 and S Series ..................... 199
4.13 Gleaner
®
S9 Series Combines .............................................................................................................. 202
4.13.1 Setting up Header – Gleaner
®
S9 Series ........................................................................................ 202
4.13.2 Setting up Reel Settings – Gleaner
®
S9 Series................................................................................. 207
4.13.3 Setting up Automatic Header Controls – Gleaner
®
S9 Series ............................................................. 208
4.13.4 Calibrating Header – Gleaner
®
S9 Series ....................................................................................... 210
4.13.5 Operating Header – Gleaner
®
S9 Series ........................................................................................ 214
4.13.6 Header In-Field Settings – Gleaner
®
S9 Series ................................................................................ 215
4.14 John Deere 50 Series Combines........................................................................................................... 218
4.14.1 Checking Voltage Range from Combine Cab .................................................................................. 218
4.14.2 Calibrating Auto Header Height .................................................................................................. 220
4.14.3 Setting Sensitivity of Auto Header Height Control .......................................................................... 222
4.14.4 Adjusting Threshold for Drop Rate Valve ...................................................................................... 223
4.14.5 Operating Auto Header Height ................................................................................................... 223
4.15 John Deere 60 Series Combines........................................................................................................... 226
TABLE OF CONTENTS