MacDon FlexDraper FD75 - Page 13

214323 xi Revision B
4.15.1 Checking Voltage Range from Combine Cab – John Deere 60 Series .................................................. 226
4.15.2 Calibrating Auto Header Height Control – John Deere 60 Series........................................................ 228
4.15.3 Turning Off Accumulator – John Deere 60 Series............................................................................ 230
4.15.4 Setting Sensing Grain Header Height – John Deere 60 Series ............................................................ 230
4.15.5 Setting Sensitivity of Auto Header Height Control – John Deere 60 Series........................................... 231
4.15.6 Adjusting Threshold for Drop Rate Valve – John Deere 60 Series....................................................... 232
4.16 John Deere 70 Series Combines........................................................................................................... 233
4.16.1 Checking Voltage Range from Combine Cab – John Deere 70 Series .................................................. 233
4.16.2 Calibrating Feeder House Speed – John Deere 70 Series.................................................................. 236
4.16.3 Calibrating Auto Header Height Control – John Deere 70 Series........................................................ 236
4.16.4 Setting Sensitivity of Auto Header Height Control – John Deere 70 Series........................................... 237
4.16.5 Adjusting Manual Header Raise/Lower Rate – John Deere 70 Series .................................................. 238
4.17 John Deere S and T Series Combines .................................................................................................... 240
4.17.1 Checking Voltage Range from Combine Cab – John Deere S and T Series............................................ 240
4.17.2 Calibrating Feeder House Fore-Aft Tilt Range – John Deere S and T Series .......................................... 242
4.17.3 Calibrating Auto Header Height Control – John Deere S and T Series ................................................. 245
4.17.4 Setting Sensitivity of Auto Header Height Control – John Deere S and T Series .................................... 247
4.17.5 Adjusting Manual Header Raise/Lower Rate – John Deere S and T Series ........................................... 248
4.17.6 Setting Preset Cutting Height – John Deere S and T Series ............................................................... 249
4.18 John Deere S7 Series Combines ........................................................................................................... 253
4.18.1 Setting up Header – John Deere S7 Series..................................................................................... 253
4.18.2 Checking Voltage Range from Combine Cab – John Deere S7 Series .................................................. 256
4.18.3 Calibrating Feeder House – John Deere S7 Series ........................................................................... 258
4.18.4 Calibrating Header – John Deere S7 Series .................................................................................... 261
4.19 New Holland Combines CR/CX Series – CR Series, Model Year 2014 and Earlier ........................................... 265
4.19.1 Checking Voltage Range from Combine Cab – New Holland CX/CR Series ......
..................................... 265
4.19.2 Engaging Auto Header Height Control – New Holland CR/CX Series ................................................... 267
4.19.3 Calibrating Auto Header Height Control – New Holland CR/CX Series................................................. 268
Calibrating Maximum Stubble Height ........................................................................................... 270
4.19.4 Adjusting Header Raise Rate – New Holland CR/CX Series................................................................ 271
4.19.5 Setting Header Lower Rate – New Holland CR/CX Series.................................................................. 271
4.19.6 Setting Auto Header Height Control Sensitivity – New Holland CR/CX Series .. ..................................... 272
4.19.7 Setting Preset Cutting Height – New Holland CR/CX Series............................................................... 272
4.20 New Holland Combines – CR Series, Model Year 2015 and Later ............................................................... 274
4.20.1 Engaging Auto Header Height Control – New Holland CR Series ........................................................ 274
4.20.2 Checking Voltage Range from Combine Cab – New Holland CR Series ................................................ 277
4.20.3 Setting up Reel Speed – New Holland CR Series ............................................................................. 279
4.20.4 Calibrating Auto Header Height Control – New Holland CR Series ..................................................... 281
4.20.5 Setting Auto Height – New Holland CR Series ................................................................................ 283
4.20.6 Setting Maximum Work Height – New Holland CR Series................................................................. 284
4.20.7 Configuring Reel Fore-Aft, Header Tilt, and Header Type – Some New Holland CR Series Models............ 285
Chapter 5: Header Attachment/Detachment........................................................................................ 289
5.1 Adapter Setup.................................................................................................................................... 289
TABLE OF CONTENTS