Lupus Electronics XT 1 Plus

To Next Page

To Previous Page

 Press the button to repeat (send out) the saved signal, e.g. to switch the fan

on or off.

 Five appliances with eight functions (signals) respectively can be programmed for

each universal IR controller.

Main Page

Table of Contents2
Table of Content2
Introduction7
- Difference of the Alarm Panels8
- Disclaimer9
- Important Safety Information11
- If You Find Defects12
- Designated Use12
The most Important Chapters for the Initial Setup13
Putting the LUPUSEC-XT2 (Plus) into Operation14
- Place of Installation14
- Connecting the XT1 Plus Alarm Panel15
- Connecting the XT2 (Plus) Alarm Panel17
- Connecting the XT3 Alarm Panel19
- Additional Mounting Information23
Description of the Leds24
Access to the Web Interface of the LUPUSEC-XT Alarm Panel27
User Interface of the Alarm Panel33
- Home Menu38
- Configure Overview Page42
- Sensors46
- List47
- Edit Sensor50
- Add54
- Range55
- Universal Remote Control56
- Smart Home Menu58
- Automation58
- Home Automation Settings62
- Condition62
- Schedule64
- Action65
- Examples68
- Wireless Plugs76
- Cameras81
- Capture84
- Power Consumption85
- Temperature History86
- Scenarios87
- Alarm System88
- Settings88
- Siren Settings95
- Report100
- PIN Codes105
Settings107
- Network107
- E-Mail Account110
- SMS Account112
- SIM Card114
- Device Integration117
- System Menu120
- Status120
- Logs122
- Password123
- Firmware125
Factory Reset128
- Logout129
Remote Access Via the Internet130
- Ipv4 / Ipv6 Problem130
- Port Forwarding131
  - Port Forwarding - Brief Instructions (Currently Only in German)131
- Access Via the LUPUS App (for Android + Ios)132
  - Profile List140
  - Usage of the Alarm Panel App141
Alarm Test146
Description of Sensors and Controls147
Overview of Sensors Compatibility148
- The Internal I/O Terminal of the XT3151
- Integration of Lamps of Other Manufacturers153
- 12 / 24 V Wireless Relay156
- Connecting the 12 / 24 V Wireless Relay and Putting It into Operation157
Channel Relay159
- Connecting the Single Channel Relay and Putting It into Operation160
Channel Relay162
- Connecting the Double Channel Relay and Putting It into Operation163
360° PIR Motion Detector165
- Connecting the 360° PIR Motion Detector and Putting It into Operation166
CO Detector168
- Connecting the CO Detector and Putting It into Operation168
Curtain Motion Detector170
- Connecting the Curtain Motion Detector and Putting It into Operation171
Door Contact174
- Connecting the Door Contact and Putting It into Operation175
Door Contact V2177
- Connecting the Door Contact V2 and Putting It into Operation178
Dual-Way Motion Detector181
- Connecting the PIR / Microwave Motion Detector and Putting It into Operation182
Electric Meter185
- Connecting the Electric Meter and Putting It into Operation186
Emergency Button189
- Connecting the Emergency Button and Putting It into Operation190
Glass Breaking Sensor192
- Connecting the Glass Breaking Sensor and Putting It into Operation192
Glass Breaking Sensor V2195
- Connecting the Glass Breaking Sensor V2 and Putting It into Operation196
Heat Detector198
- Connecting the Heat Detector and Putting It into Operation198
Indoor Siren200
- Connecting the Indoor Siren and Putting It into Operation200
Keypad206
- Connecting the Keypad and Putting It into Operation207
Light Sensor211
- Connecting the Light Sensor and Putting It into Operation212
Light Switch V2214
- Installation of Light Switch V2215
Lockswitch Contact219
- Connecting the Lockswitch Contact and Putting It into Operation220
Magnetic Lock222
- Installing the Magnetic Lock to the Door and Putting It into Operation223
Mechanical Lock224
- Installing the Mechanical Lock to the Doorframe and Putting It into Operation225
Medical Emergency Controller227
- Connecting the Medical Emergency Controller and Putting It into Operation227
Outdoor Keypad229
- Connecting the Outdoor Keypad with Tag Reader and Putting It into Operation231
Outdoor Siren V2239
- Connecting the Outdoor Siren V2 and Putting It into Operation240
Panic Button245
- Connecting the Panic Button and Putting It into Operation245
PIR Motion Detector V2246
- Connecting the PIR Motion Detector V2 and Putting It into Operation247
PIR Network Camera V3250
- Connecting the PIR Network Camera V3 und Putting It into Operation251
Radiator Valve Thermostat V2254
- Installation of Radiator Valve Thermostat V2256
Relay with Power Meter V2260
- Connecting Relay with Power Meter for XT2 Plus and Putting It into Operation261
Remote Control V2263
- Connecting the Remote Control V2 and Putting It into Operation264
Remote Controlled Mains Socket with Power Meter and Zigbee Repeater265
- Connecting the Wireless Socket and Putting It into Operation266
Scenario Switch V2268
- Connecting the Scenario Switch V2 and Putting It into Operation269
Sensor Input271
- Connecting the Sensor Input and Putting It into Operation272
Sensor Input (9 Fold)274
- Calibrating the Sensor Input (9 Fold)276
Shutter Relay V2278
- Connecting the Shutter Relay V2 and Putting It into Operation281
Small Indoor Siren V2284
- Connecting the Small Indoor Siren and Putting It into Operation285
Smoke Detector V2287
- Connecting the Smoke Detector V2 and Putting It into Operation289
Status Display292
- Connecting the Status Display and Putting It into Operation293
Tag Reader V2295
- Connecting the Tag Reader V2 and Putting It into Operation296
Temperature Sensor V2298
- Connecting the Temperature Sensor and Putting It into Operation298
Temperature Sensor with Display V2300
- Connecting the Temperature Sensor and Putting It into Operation300
Temperature Sensor with External Probe302
- Connecting the Temperature Sensor with External Probe and Putting It into Operation303
Top-Hat Rail Relay304
- Connecting the Top-Hat Rail Relay and Putting It into Operation305
Universal IR Controller307
- Connecting the Universal IR Controller and Putting It into Operation308
- Learn and Test IR Signals308
- Installation311
- IR LED Selection and Operation312
Upgrade Dongle to XT2 Plus313
Vibration Sensor314
- Connecting the Vibration Sensor and Putting It into Operation315
Water Sensor317
- Connecting the Water Sensor and Putting It into Operation317
Water Sensor V2319
- Connecting the Water Sensor V2 and Putting It into Operation320
Wireless Relay322
- Connecting the Wireless Relay and Putting It into Operation322
Wireless Repeater V2324
- Connecting the Wireless Repeater V2 and Putting It into Operation325

Lupus Electronics XT 1 Plus - Page 57

Table of Contents