Olympus EPOCH 1000 Series - Table 35 EPOCH 1000 I Supported Wedges; Table 34 EPOCH 1000 I Supported PA Probes; Probe and Wedges Specifications

910-269-EN, Rev. B, June 2011
318 Chapter 19
19.4 Probe and Wedges Specifications
The EPOCH 1000i supports a series of phased array probes to meet the demands of
critical inspections (see
Table 34 on page 318). These probes include standard weld
inspection probes, specialized probes for specific code compliance, and a standard
64-element probe (used with other Olympus phased array products) for linear
scanning.
Table 34 EPOCH 1000i supported PA probes
a
a.All probes supplied with 2.5 m cable and OmniScan style connector. For other variations contact Olympus.
Part Usage/Code compliance
Frequency
(MHz)
Number of
elements
Pitch
Active
aperture
(mm)
Elevation
(mm)
Dimensions
in mm (in.)
L x W x H
2.25L8-A10P General purpose 2.25 8 1.2 9.6 x 10 10 22.5
(0.89)
15.6
(0.61)
20.0
(0.79)
5L16-A10P 5.0 16 0.6 9.6 x 10 10 22.5
(0.89)
15.6
0.61)
20.0
(0.79)
10L16-A10P 10.0 16 0.6 9.6 x 10 10 22.5
(0.89)
15.6
(0.61)
20.0
(0.79)
2.25L16-AWS1 AWS D1.1/D1.5 2.25 16 0.94 15 x 15 16 37.6
(1.48)
25.4
(1.0)
17.8
(0.70)
2L8-DGS1 Europe, Integral Wedge/
DGS/AVG
2.0 8 1 8 x 9 9 27.3
(1.07)
16.8
(0.66)
22.3
(0.88)
4L16-DGS1 4.0 16 0.5 8 x 9 9 27.3
(1.07)
16.8
(0.66)
22.3
(0.88)
5L64-A12 General purpose 5.0 64 0.6
9.6 x 10
b
b.For 16-element pulse group
10 44.6
(1.76)
22.5
(0.89)
20.0
(0.79)
Table 35 EPOCH 1000i supported Wedges
Part Matching probes
Nominal
refracted beam
angle (in steel)
Sweep (°)
Probe
orientation
Dimensions
in mm (in.)
L x W x H
SA10P-0L 2.25L8-A10P
5L16-A10P
10L16-A10P
0° LW –30 to 30 Normal 25.4
(1.0)
23.1
(0.91)
20.0
(0.79)
SA10P-N55S 2.25L8-A10P
5L16-A10P
10L16-A10P
55° SW 30 to 70 Normal 23.0
(0.91)
23.2
(0.91)
14.2
(0.56)
SAWS-0L 2.25L16-AWS 0° LW –30 to 30 Normal 38.0
(1.49)
37.6
(1.48)
40.0
(1.57)
SAWS-N55S 2.25L16-AWS 55° SW 30 to 70 Normal 45.3
(1.78)
38.0
(1.49)
30.3
(1.19)
Downloaded from ManualsNet.com search engine