5
22.4. Adjustment track record....................................................................................................................... 82
23. SOFTWARE UPDATE...............................................................................................................................82
23.1. ON-LINE updating................................................................................................................................83
23.2. Update from pen drive ......................................................................................................................... 84
23.3. Changes in software ............................................................................................................................ 85
24. REMOTE DESKTOP.................................................................................................................................. 86
25. SPECIAL FUNCTIONS OF WORKING MODES........................................................................................ 86
25.1. Working modes accessibility................................................................................................................ 88
25.2. Save mode...........................................................................................................................................88
25.3. Down-weighing .................................................................................................................................... 89
25.4. Checkweighing .................................................................................................................................... 90
25.5. Tare mode ........................................................................................................................................... 90
25.6. Labelling mode .................................................................................................................................... 91
25.6.1. Setting of the number of labels to print...................................................................................... 91
25.6.2. Setting of the number of cumulative labels to print.................................................................... 92
25.6.3. Setting of the number of CC labels to print................................................................................ 92
25.6.4. Automatic triggering of cumulative labels .................................................................................. 92
25.6.5. Automatic triggering cumulative labels of cumulative labels...................................................... 94
25.7. Statistics .............................................................................................................................................. 95
25.8. Differential weighing............................................................................................................................. 96
25.8.1. Local settings............................................................................................................................ 96
25.8.2. Reporting realized processes of differential weighing................................................................ 97
25.9. Peak hold.............................................................................................................................................97
25.10. Min 2, Max 2 thresholds active........................................................................................................... 98
25.11. Information about saved measurement .............................................................................................. 99
25.12. Standard printout................................................................................................................................ 99
25.13. Packaging quantity query ................................................................................................................. 101
26. WORKING MODE - WEIGHING .............................................................................................................. 101
26.1. Starting the working mode ................................................................................................................. 101
26.2. Local setting of a working mode......................................................................................................... 102
27. WORKING MODE – PARTS COUNTING................................................................................................ 102
27.1. Starting the working mode ................................................................................................................. 103
27.2. Local settings of the working mode.................................................................................................... 103
27.2.1. Automatic correction of reference mass .................................................................................. 104
27.2.2. Minimum reference mass........................................................................................................ 105
27.3. Setting a reference unit by entering known piece mass ..................................................................... 105
27.4. Setting a reference unit by weighing a sample................................................................................... 106
27.5. Setting the reference mass by entering single piece mass directly to the database........................... 107
27.6. Inscribing the unit mass to the database............................................................................................ 107
28. WORKING MODE – PERCENT SETUP (DEVIATIONS) ......................................................................... 107
28.1. Starting the operating mode............................................................................................................... 108
28.2. Local settings of the working mode.................................................................................................... 108
28.3. Reference unit mass estimated by weighment................................................................................... 109
28.4. Reference unit mass inscribing into the memory................................................................................ 109
29. WORKING MODE - DOSING................................................................................................................... 109
29.1. Starting the working mode ................................................................................................................. 110
29.2. Dosing process structure ................................................................................................................... 110
29.3. Local setting of a working mode......................................................................................................... 111
29.4. Description of functions and setting dosing process........................................................................... 112
29.5. Creating a new dosing process.......................................................................................................... 115
29.6. Instances of dosing processes........................................................................................................... 116
29.6.1. Instance 1 – Manual dosing process of 4 ingredients on 2 weighing platforms........................ 116
29.6.2. Instance 2 – Automatic dosing of 2 ingredients on 2 weighing platforms................................. 118
29.6.3. Instance 3 – Mixed dosing process ......................................................................................... 120
29.7. Reporting of completed dosing processes ......................................................................................... 123
30. WORKING MODE – FORMULATION...................................................................................................... 124
30.1. Starting the working mode ................................................................................................................. 124
30.2. Local setting of a working mode......................................................................................................... 125
30.3. Creating a new formulation ................................................................................................................ 126
30.4. Formula making process.................................................................................................................... 129
30.5. Reporting from completed formula making processes........................................................................ 131
31. WORKING MODE – PGC (PREPACKAGED GOODS CONTROL)......................................................... 132
31.1. Starting the working mode ................................................................................................................. 133
31.2. Control settings mode window ........................................................................................................... 134
31.3. Local setting of a working mode......................................................................................................... 135
To Next Page
Loading...
Need help?
General
