Rohde & Schwarz CMU 200 - Page 414

Index CMU
1100.4903.12 I.2 E-8
syntax elements ...................................................... 5.12
universal.................................................................... 8.4
Comment ......................................................................... 4.5
Common Command.................................................. 5.7, 6.1
Communicate (Setup)
remote control ......................................................... 6.11
Condition register........................................................... 5.17
Configuration ................................................................. 3.16
firmware................................................................... 1.18
measurement........................................................... 3.17
Configuration file............................................................ 4.22
Configuration tree ............................................................ 4.3
Connection
controller.................................................................. 1.14
external keyboard.................................................... 1.16
IEC bus.................................................................... 1.14
monitor .................................................................... 1.16
RS-232 .................................................................... 1.15
Connection Control.......................................... 3.5, 3.7, 3.16
remote control (RF) ................................................. 6.26
RF............................................................................ 4.57
Content/Destination ....................................................... 4.23
Continuous............................................................ 4.39, 5.34
Control lines (GPIB bus).................................................. 8.3
Controller connection..................................................... 1.14
Controls ........................................................................... 3.1
Copy .............................................................................. 4.32
Copy File........................................................................ 6.20
Copy non volatile ram to disk......................................... 1.25
Counting ........................................................................ 5.34
Current.................................................................. 4.46, 4.55
D
Data ............................................................................... 4.22
bits (RS-232) ............................................................. 8.7
lines (GPIB bus) ........................................................ 8.2
set............................................................................ 5.14
Data Bits ............................................................... 4.12, 6.12
Date ...................................................................... 4.16, 6.14
DC Coupling .................................................................. 6.84
DC Voltage .................................................................... 4.77
DCL................................................................................ 5.13
Decimal point................................................................. 5.10
Default ............................................................................. 4.2
Default Scale ................................................................. 4.85
Default Settings ............................................................. 4.38
Defragment disk............................................................. 1.25
Delay.............................................................................. 6.47
Delete (Data) ................................................................. 4.31
Delete non volatile ram.................................................. 1.25
Delete software.............................................................. 1.19
Delimiter......................................................................... 5.13
Delta marker .................................................................. 4.42
Destination....................................................................... 4.5
Detect Mode .................................................................. 4.56
Device messages ............................................................ 5.7
Device model................................................................. 5.13
Device-specific commands.............................................. 5.7
Dialog box...................................................................... 3.10
Dir. View/Content........................................................... 4.30
Display (Multitone)......................................................... 4.85
Display line ................................................. 4.51, See D-line
Display mode................................................................. 3.19
Display Mode
Power (NS).............................................................. 4.46
Spectrum................................................................. 4.55
Display/Marker (Power) ................................................. 4.42
Display/Marker (Power, NS) .......................................... 4.52
Distortion........................................................................ 4.77
Distortion Frequency...................................................... 4.79
D-line
Power ...................................................................... 4.42
Spectrum..................................................................4.52
Double dagger (
# )...........................................................5.12
Dynamic range...............................................................4.59
E
Edit service tables..........................................................1.24
Editor..............................................................................3.10
EMC ...............................................................................1.13
Enable options ...............................................................4.14
Enable register...............................................................5.17
EOI (command line) .........................................................5.9
Error messages................................................................9.1
VersionManager.......................................................1.26
Error queue ....................................................................5.26
ESE (event status enable register) ................................5.21
Event reporting system...................................................5.31
Event status enable register (ESE)................................5.21
Exit .................................................................................1.24
Exit Assign .......................................................................4.7
Expanding table ...............................................................3.8
Exponent........................................................................5.10
Ext. Att. Input.........................................................4.66, 6.39
Ext. Att. Output......................................................4.65, 6.40
Ext. Trigger (AUX 3/4)...........................................4.71, 6.29
External keyboard ..........................................................1.16
External trigger...............................................................4.70
F
FETCh command ...........................................................5.36
FETCh status .................................................................5.32
File Manager ..................................................................4.22
Filename...........................................................................4.5
Filename Default............................................................4.10
Filter
AF Analyzer .............................................................6.70
Multione ...................................................................4.92
Multitone ..................................................................6.83
Firmware configuration...................................................1.18
Firmware update ............................................................1.18
Firmware update after board change .............................1.24
First AF channel.............................................................6.75
Fixed band pass....................................................4.81, 6.70
Free run trigger mode.....................................................4.70
Freq................................................................................4.46
Frequency ......................................................................4.56
AF generator............................................................4.80
Power.......................................................................6.46
reference (Audio) .....................................................6.70
remote control (Power) ...................................6.46, 6.61
remote control (Spectrum) .......................................6.53
RF analyzer.....................................................4.38, 6.30
RF generator..........................................4.63, 6.34, 6.38
variable band pass..........................................4.82, 6.70
Frequency Hopping...............................................4.63, 6.36
Front view.........................................................................1.1
Full Span........................................................................4.50
Function group .................................................................4.6
Fuses..............................................................................1.11
G
Gain................................................................................4.65
Generator
Analzer/Generator..................................4.37, 4.41, 4.51
Audio...............................................................4.76, 6.73
RF ............................................................................4.60
Generator 1 Frequency ..................................................6.74
Generator 1 Level...........................................................6.74
Generator 1 Signal .........................................................6.74
Generator command ......................................................5.33
Generator control ...........................................................5.33