CMU List of Commands
1100.4903.12 6.91 E-10
Command Parameters Remarks Page
Subsystem SYNChronize (reference frequency)
CONFigure:SYNChronize:FREQuency:REFerence 10 kHz to 52 MHz with query 6.23
[SENSe:]SYNChronize:FREQuency:REFerence:LOCKed? ON | OFF query only 6.23
CONFigure:SYNChronize:FREQuency:REFerence:MODE INTernal | EXTernal with query 6.23
SYSTem (system parameters)
SYSTem:ERRor? query only 6.5
SYSTem:NONVolatile:DISable no query 6.5
SYSTem:VERSion? query only 6.5
SYSTem:TIMe:DATe YYYY,MM,DD with query 6.14
SYSTem:TIMe:TZONe -12 to +12,-59 to +59 with query 6.13
SYSTem:TIMe[:TIMe] 0 to 23,0 to 59,0 to 59 with query 6.13
TRACe (remote report)
TRACe:REMote:MODE:DISPlay ON | OFF - 6.17
TRACe:REMote:MODE:ERRor ON | OFF - 6.17
TRACe:REMote:MODE:FILE ON | OFF - 6.17
TRACe:REMote:MODE:OUTLines 1 to 4 - 6.18
TRACe:REMote:MODE:SQR ON | OFF - 6.17
Table 6-2 List of remote-control commands: RF measurements
Command Parameters Remarks Page
Subsystem CORRection:LOSS (Ext. Attenuation)
[SENSe:]CORRection:LOSS:INPut<nr>[:MAGNitude] –50 dB to 50 dB with query 6.39
SOURce:CORRection:LOSS:INPut<nr>[:MAGNitude] –50 dB to 50 dB with query 6.39
[SENSe:]CORRection:LOSS:OUTPut<nr>:AUXTx[:MAGNitude] –50 dB to 50 dB with query 6.40
SOURce:CORRection:LOSS:OUTPut<nr>:AUXTx[:MAGNitude] –50 dB to 50 dB with query 6.40
[SENSe:]CORRection:LOSS:OUTPut<nr>[:TX][:MAGNitude] –50 dB to 50 dB with query 6.40
SOURce:CORRection:LOSS:OUTPut<nr>[:TX][:MAGNitude] –50 dB to 50 dB with query 6.40
SOURce:DM:CLOCk:STATe ON | OFF with query 6.40
Subsystem DM:CLOCk (Synchronization)
SOURce:DM:CLOCk:FREQuency 1.250 MHz to 40.000 MHz with query 6.41
SOURce:DM:CLOCk:STATe ON | OFF with query 6.40
Subsystem INPut, OUTput ( )
INPut[:STATe] ON | OFF with query 6.39
OUTPut[:STATe] ON | OFF with query 6.39
Subsystem IQIF (I/Q-IF Signals)
IQIF:DEFault ON | OFF with query 6.43
CONFigure:IQIF:RXPath BYP | BYIQ | XOIO | IOIO |
IOXO
with query 6.42
CONFigure:IQIF:RXTXcombined BYP | BYIQ | XOIO | IOIO |
IOXO | FPAT | UDEF
with query 6.42
To Next Page
Loading...
