Barco HDF W series Service Manual

Index
LPS failure fan 1 38
LPS failure fan 1 & 2 35
LPS failure fan 2 39
LPS failure pfc driver 39
LPS failure power stage driver 39
LPS internal error 38
LPS internal voltage error 38
LPS invalid parameters 35
LPS mains voltage too high 38
LPS mains voltage too low 37
LPS no lamp ignition detected 35
LPS output current too high 36
LPS output current too low 3 6
LPS output power too high 35
LPS output power too low 35
Lps read failed 93
Lps reply no ac k 94
LPS requested outpu t power too high with low mains voltage 38
LPS start-up fail LPS power stage 35
LPS start-up fail PFC power stage 35
LPS Temperature ambient too high 36–37
LPS temperature heatsink output diode to o high 37
LPS temperature primary heatsink 1 too high 36
LPS temperature primary heatsink 2 too high 36
LPS temperature trans former too high 37
Lps write failed 93
Lseek failed 92
Lsm read failed 94
Lsm reply no a ck 94
Lsm write failed 93
Mains voltage high 74–75
Mains voltage low 74
Mcb read failed 93
Mcb reply no a ck 94
Mcb write failed 93
Mmap failed 9 3
Motor board calibration 84
No dmx shutdown 89
No m emory 91
no signal shutdown 89
Non blocked signal 91
Opening shutter failed 84
Overtemp 72
Overtemperature dimming 88
Port timeout 91
Power interrupt 71
Power supply primary DCDC temp high 69
Power supply primary DCDC temp low 68– 69
Power supply primary DCDC temp open 69
Power supply primary PFC temp high 70
Power supply pr imary PFC temp low 69–70
Power supply primary PFC temp open 70–71
Power supply secondary temp high 67–6 8
Power supply secondary temp low 67
Power supply secondary temp open 68
Power supply secondary temp short 68
Projector type invalid 90
Pump voltage high 75
Pump voltage low 75
Read failed 92
Read lamp status failed 35
Reading lamp info module 87
Recieve Overflow 92
Recieve Parity 92
Red DMD temp high 54–55
Red DMD temp low 53–54
Red DMD temp open 55
Red DMD temp short 56
Red form. s tart failed 33
Rodintemphigh 66
Rod in temp low 65–66
Rod in temp open 67
Rodintempshort 67
Rs485 selection 91
Setting FCB mode 53
Setting XLR control 53
Shutter current too high 86
Shutter time out 85
Spi Ioctl failed 92
Storage: restoring without any preceding storing 96
Storage: successful restoring 96
Storage: successful restoring with fall back mgt file 96
Storage: unsuccessful restoring 96
Tilt orientation invalid 89
Tilt rotation not allo wed 87–88
Transmit overflow 92
Usb restoring settings failed 90
Usb saving settings failed 90
Vertical lens shift driver 85
Vertical lens shift end of range 84–85
Vertical lens shift stopped 87
Watchdog 72
Write failed 92
Xlr overload 76
Error code number 33–96
100000 91
100001 91
100002 91
100003 91
100004 91
100005 91
100006 91
100007 91
100008 91
100009 91
100010 91
100011 92
100012 92
100013 92
100014 92
100015 92
100016 92
100017 92
100018 92
100019 92
100020 92
100021 92
100022 93
100023 93
100024 93
100025 93
100026 93
100027 93
100028 93
100029 93
100030 93
100031 93
100032 93
100033 94
100034 94
100035 94
100036 94
100037 94
100038 94
100039 94
100040 94
100041 94
100042 94
100043 94
100044 95
100045 95
100046 95
100047 95
100048 95
100049 95
100050 95
100051 95
100052 95
100053 95
100054 95
100055 96
100056 96
R5905312 HDF W SERIES 24/01/2013
327

Barco HDF W series Specifications

General

Brand	Barco
Model	HDF W series
Category	Projector
Language	English