Barco HDF W series - Installation Manual

Barco HDF W series

267 pages

To Next Page

To Next Page

Loading...

HDF W s eries

Installation manual

R5905158/01

10/07/2012

Table of Contents

Default Chapter5
- Table of Contents5
1 Safety9
- General Considerations9
- Important Safety Instructions10
- Important Warnings Concerning HDF W Series Flight Cases12
2 Conﬁgurations, Requirements and Restrictions15
- Installation Requirements15
- Unpacking the Projector16
- HDF W Series Flight Case17
- Rear Projection18
- Projector Conﬁgurations18
- Positioning the Projector19
- Projector Air Inlets and Outlets21
- Free Download of Projector Toolset21
- Installation Process Overview22
3 Physical Installation23
- Remote Control Unit (RCU)23
- Lenses27
- Power Connection37
- Suspension of the HDF W Series Projector with Rigging Clamps38
4 Input & Communication43
- Introduction43
- Input Source Connections44
- Communication Connections45
5 Getting Started49
- RCU & Local Keypad49
- Terminology Overview49
- Power on Projector51
- Software Overview53
- Switching to Standby54
- Power off Projector54
- Status Leds55
- Using the RCU55
- Projector Address57
  - Displaying and Programming Addresses into the RCU57
  - Controlling the Projector57
- Source Selection57
- Alignment of a Table Mount HDF W Series Projector58
- Alignment of a Ceiling Mount HDF W Series Projector59
6 Quick Set up Adjustment61
- Text Boxes on or off61
- Quick Lens Adjustment Via LENS Key61
- Direct Lens Adjustment (RCU)63
- Quick Picture in Picture64
- Quick Language Selection64
7 Start up of the Adjustment Mode67
- About the Adjustment Mode67
- About the Use of the Remote Control and the Local Keypad67
- Start up the Adjustment Mode67
- Navigation and Adjustments68
- Menu Memory69
- Shortcut Keys to the Menus69
- Test Patterns in Adjustment Mode69
- Help Information in Adjustment Mode70
8 Input71
- Input Menu Overview71
- Slot Module Type72
- Input Locking75
- Native Resolution77
- No Signal78
- Edid81
9 Image87
- Image Menu Overview87
- Start up the Image Adjustments88
- Image Settings88
- Aspect Ratio97
- Timings99
  - Source Timings99
  - Advanced Timings, Clamp Delay - Clamp Width100
- Image File Services102
- Save Custom Settings109
- Splash Image109
10 Layout111
- Layout Menu Overview111
- Introduction111
- Main Window112
- Pip Window115
- Layout File Services120
- Zoom - Focus - Shift Windows124
11 Lamp127
- Lamp Menu Overview127
- Lamp Power Mode127
- Lamp Power128
- Auto Dimming When on Pause129
- Auto Dimming When no Signal130
- Auto Dimming When Over-Temperature130
- CLO Mode (Constant Light Output Mode)131
- CLO Targets133
- LPS Power134
- Lamp Identiﬁcation134
- Z-Axis Adjustment135
12 Alignment137
- Alignment Menu Overview137
- Orientation138
- Lens Adjustment, Zoom - Focus139
- Lens Adjustment, Shift140
- Lens Adjustment, MID Position141
- Home Lens at Startup142
- Calibrate Lens142
- Warping143
- Blanking Adjustment151
- Contrast-Intensity153
- Gamma154
- Internal Patterns154
- Color Space155
- Scenergix157
13 Projector Control167
- Projector Control Menu Overview167
- Individual Projector Address168
- Projector Common Address168
- Serial Communication169
  - Baud Rate Setup169
  - Interface Standard170
- Network171
- IR Control Switching183
- DMX184
- Buttons190
  - Standby Button190
  - Shortcut Keys191
- Menu Position192
- Local LCD193
- Language Selection193
- Scheduler194
14 Service201
- Service Menu Overview201
- Identiﬁcation202
- What Can be Seen202
- Diagnosis203
- Internal Service Patterns211
- Convergence215
- Factory Defaults216
- USB Memory217
- Reset Formatter218
- Reﬁll Mode219
- Save Custom Settings220
- Special HD Camera Mode221
- Auto Dimming When Over-Temperature222
- Time and Date222
15 Maintenance225
- Cleaning the Lens225
- Cleaning the Exterior of the Projector225
16 Removal and Installation of the Projector Covers227
- Removal of the227
- Removal of the Side Cover228
- Removal of the Lamp Cover229
- Removal of the Input Cover229
- Installation of the230
- Installation of the Side Cover231
- Installation of the Lamp Cover232
- Installation of the Input Cover233
17 Servicing235
- Inserting an Input Module235
- Replacement of the Dust Filter on the Front Side236
- Replacement of the Dust Filter on the Bottom Side237
- Replacement of the Dust Filter on the Top Side238
- Pressure Veriﬁcation of the Liquid Cooling Circuit239
- Removal of the Lamp House239
- Installation of the Lamp House241
- Realignment of the Lamp in Its Reﬂector242
Speciﬁcations245
- Speciﬁcations of the HDF W22245
- Speciﬁcations of the HDF W26246
Dimensions249
- Dimensions of the HDF W Series Projector249
- Dimensions of the HDF W Series Flight Case250
Standard Source Files251
- C.1 Table Overview251
DMX Chart255
- DMX Chart, Basic255
- DMX Chart, Full255
- DMX Chart, Extended256
Stacking HDF W Series Projectors259
- Aligning Stacked HDF W Series Projectors261
Environmental Information265
- Disposal Information265
- Rohs Compliance265

Other manuals for Barco HDF W series

Quick Start Guide2 pages

Service Manual337 pages

Safety Manual8 pages

Related product manuals

Preview: Barco HDX

Preview: Barco FLM HD20

Barco HDX series

Preview: Barco SIM 7Q HB

Barco SIM 7Q HB

Preview: Barco F35

Preview: Barco UDX

Preview: Barco Freya

Preview: Barco RLM W8

Preview: Barco UDX Series

Barco UDX Series