Barco HDF W series Service Manual

Index
Board id: input 3 not calibrated 42
Board id: input 3 read error 41
Board id: input 3 type on wrong location 42
Board id: input 3 unknown format 41
Board id: input 3 unknown module type 41
Board id: input 3 write error 42
Board id: input 4 not calibrated 43
Board id: input 4 read error 42
Board id: input 4 type on wrong location 43
Board id: input 4 unknown format 42
Board id: input 4 unknown module type 42
Board id: input 4 write error 43
Board id: lamp info module board not accessible 48
Board id: lamp info module r ead error 48
Board id: lamp info module unknown format 48
Board id: lamp info module wr ite error 49
Board id: lamp power supply not ac cessable 53
Board id: lamp power s upply read error 53
Board id: lamp power supply unknown format 53
Board id: lamp power s upply write e rror 53
Board id: light sensor module not acces sible 50
Board id: light senso r module read error 50
Board id: light sensor module unknown format 49
Board id: light sensor module write error 50
Board id: motor control board not accessible 47
Board id: motor control board read error 47
Board id: m otor control board unknown format 47
Board id: motor control board write error 48
Board id: pm p not accessable 43
Board id: pmp read error 43
Board id: pm p unknown format 43
Board id: pmp write error 44
Board id: power backplane not accessible 45
Board id: power backplane read error 45
Board id: power backplane unknown format 45
Board id: power backplane write error 45
Board id: wa rp not accessable 52
Board id: warp read error 52
Board id: warp unknown format 52
Board id: warp write error 52
Break condition 91
Buffer overrun 92
Check airflow 88
Check ambient temperature 89
Check cooling liquid level 88
Check cooling liquid level every 6 months 88
Check dust filters 88
Closing shutter failed 84
Comm receive b usy 9 1
Comm send busy 91
Cooling startup failed 8 9
Engine air temp high 64–65
Engine air temp low 64
Engine air temp open 65
Engine air temp short 65
Engine not connected 89
Engine startup failed 90
Engine switch open 73
Fan speed cold mirror too high 77
Fan speed cold mirror too low 76–77
Fan speed electronics bottom too high 79
Fan speed electronics bottom too low 79
Fan speed electronics top bottom high 79
Fan speed electronics top too high 79
Fan speed electronics top too low 78
Fan speed engine too high 78
Fan speed engine too low 77–78
Fan speed heat exchanger front too high 80
Fan speed heat exchanger front too low 79–80
Fan speed lamp anode too high 82
Fan speed lamp anode too low 81
Fan speed lamp cathode too high 82
Fan speed lamp cathode too low 82
Fan speed mains input too high 81
Fan speed mains input too low 80–81
Fan speed power s upply left too high 83
Fan speed power supply left too low 82–83
Fan speed power s upply right too high 83
Fan speed power s upply right too low 83
Fcb read failed 93
Fcb reply no ack 94
Fcb write failed 93
Fib read failed 93
Fib reply no ack 94
Fib write failed 93
Form. PWRG ood 33
Formatter ctrl init failed 33
Formatter init failed 33
Formatter start failed 33
Framing error 92
Green DMD temp high 57
Green DMD temp low 56
Green DMD temp open 57
Green DMD temp short 57
Green form. start failed 33
Horizontal lens s hift end of rang e 8 4
Horizontal lens shift stopped 86
I2c Ioctl failed 92
Init 5-cable adc failed, input 1 95
Init 5-cable adc failed, input 2 95
Init 5-cable adc failed, input 3 95
Init 5-cable adc failed, input 4 95
Init 5-cable adv failed, input 1 95
Init 5-cable adv failed, input 2 95
Init 5-cable adv failed, input 3 95
Init 5-cable adv failed, input 4 95
Init 5-cable firmware failed, input 1 94
Init 5-cable firmware failed, input 2 94
Init 5-cable firmware failed, input 3 94
Init 5-cable firmware failed, input 4 95
Init dvi adc failed, input 1 96
Init dvi adc failed, input 3 96
Init dvi firmware failed, input 1 9 5
Init dvi firmware failed, input 2 9 6
Init dvi firmware failed, input 3 9 5
Init dvi firmware failed, input 4 9 6
Init dvi settings failed, input 2 96
Init dvi settings failed, input 4 96
Invalid device 91
Invalid filede scriptor 91
Invalid parameters 91
Invalid pointer 91
IO error 92
Lamp ignition failed 90
Lamp not inserted 89
Lamp paramete rs invalid 90
Lamp pow er supply 72
Lamp power supply interrupt 72
Lamp power supply startup failed 90
Lamp runtime maximum exceeded 88
Lamp runtime message exceeded 88
Lamp runtime shutdown exceeded 88
Lamp runtime warning exceeded 88
Lamp s tart failed 33
Lamp s top failed 34
Lamp s witch open 71
Lamp switched off due to error 90
Lamp temp high 61–62
Lamp temp low 61
Lamp tem p open 62
Lamp tem p short 62
Lens focus current too high 86
Lens focus end of range 85
Lens focus stopped 87
Lens hits p rism 86
Lens zoom current too high 86
Lens zoom end of range 85
Lens zoom stopped 87
Lim read failed 94
Lim reply no ack 94
Lim write failed 93
LPS boost voltage generation failed 35
326
R5905312 HDF W SERIES 24/01/2013

Barco HDF W series Specifications

General

Brand	Barco
Model	HDF W series
Category	Projector
Language	English