Cisco MDS 9000 Series Configuration Guide

Verifying Autozone Configuration
The following example displays the Autozone status, the zones already created, as well as uncreated (pending)
zones, by Autozone:
switch# autozone --show
Feature AutoZone : Disabled
The possible zone/zoneset configuration with AutoZone feature for currently logged-in devices
are :
zoneset name AUTOZONESET vsan 1
zone name AUTOZONE_JPG21190082_1 vsan 1
member pwwn 20:00:00:11:0d:97:00:01
member pwwn 20:01:00:11:0d:97:01:01
zone name AUTOZONE_JPG21190082_2 vsan 1
member pwwn 20:00:00:11:0d:97:00:01
member pwwn 20:01:00:11:0d:97:01:00
zone name AUTOZONE_JPG21190082_3 vsan 1
member pwwn 20:00:00:11:0d:97:00:00
member pwwn 20:01:00:11:0d:97:01:01
zone name AUTOZONE_JPG21190082_4 vsan 1
member pwwn 20:00:00:11:0d:97:00:00
member pwwn 20:01:00:11:0d:97:01:00
The following example shows how to check for the zoning configuration that Autozone creates for any unzoned
devices and then apply those changes. In this example, Autozone is disabled so that zoning is updated only
once and there is no periodic zoning by Autozone.
switch# autozone --showpending
Feature AutoZone : Disabled
zoneset name AUTOZONESET vsan 1
zone name AUTOZONE_JPG21190082_1 vsan 1
member pwwn 20:00:00:11:0d:97:00:00
member pwwn 20:01:00:11:0d:97:01:00
switch# autozone --update
Configuring zones for vsan 1
AUTOZONE_JPG21190082_1
Configuring zoneset for vsan 1
Activating the zoneset. Please wait...
Configured zoneset AUTOZONESET for vsan 1 successfully.
The following example shows how to verify if the Autozone feature is already enabled and if there are currently
unzoned devices:
switch# autozone --showpending
Feature AutoZone : Enabled
zoneset name AUTOZONESET vsan 1
zone name AUTOZONE_JPG21190082_2 vsan 1
member pwwn 20:00:00:11:0d:97:00:01
member pwwn 20:01:00:11:0d:97:01:00
zone name AUTOZONE_JPG21190082_3 vsan 1
member pwwn 20:00:00:11:0d:97:00:00
member pwwn 20:01:00:11:0d:97:01:01
zone name AUTOZONE_JPG21190082_4 vsan 1
member pwwn 20:00:00:11:0d:97:00:01
member pwwn 20:01:00:11:0d:97:01:01
The following example shows how to obtain information about the autozone command:
Cisco MDS 9000 Series Fabric Configuration Guide, Release 8.x
49
Configuring and Managing Zones
Verifying Autozone Configuration

Cisco MDS 9000 Series Specifications

General

Category	Switch
Operating System	Cisco NX-OS
Ports	Varies by model
Protocols	Fibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
Redundancy	Redundant supervisors, power supplies, and fans
Management	Cisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization Support	VSANs (Virtual SANs)
Security Features	Fibre Channel Security Protocol (FC-SP)
Hot Swappable Components	power supplies, fans
Power Supply Options	AC and DC options available