Cisco MDS 9000 Series Configuration Guide

Zoneset not present
2. Verify the existing device logins using the show fcns database command:
switch# show fcns database
VSAN 1:
-----------------------------------------------------------------------
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
-----------------------------------------------------------------------
0xee0000 N 20:00:00:11:0d:97:00:00 scsi-fcp:init
0xee0020 N 20:01:00:11:0d:97:01:00 scsi-fcp:target
0xee0400 N 10:00:00:de:fb:74:e8:31 (Cisco) ipfc
Total number of entries = 2
3. Create zones and a zoneset on VSAN 1 automatically and schedule a timer to check for new device logins
on the Cisco MDS switch using the autozone command:
switch# autozone
This command will create and activate single-initiator and single-target zones for all
end-devices are already logged-in automatically; that may lead to more tcam entries and
also RSCN load on network. Please use AutoZone judiciously.
AutoZone feature is enabled
Device with pwwn 10:00:00:de:fb:74:e8:31 is not registered with FC4-type Init or Target.
Hence, it will be ignored for AutoZone configuration.
Configuring zones for vsan 1
AUTOZONE_JPG21190082_1
Configuring zoneset for vsan 1
Activating the zoneset. Please wait...
Configured zoneset AUTOZONESET for vsan 1 successfully.
4. Verify the zone configuration using the show zoneset active vsan 1 command:
switch# show zoneset active vsan 1
zoneset name AUTOZONESET vsan 1
zone name AUTOZONE_JPG21190082_1 vsan 1
* fcid 0xee0000 [pwwn 20:00:00:11:0d:97:00:00]
* fcid 0xee0020 [pwwn 20:01:00:11:0d:97:01:00]
You can see that a new zoneset named AUTOZONESET is created and a new zone of the format
AUTOZONE_<SwitchSerialNumber>_<number> is created and the devices are added to this zoneset:
5. Add Initiator 2 and Target 2 to the network:
6. Verify the new device logins using the show fcns database command:
switch# show fcns database
VSAN 1:
-----------------------------------------------------------------------
FCID TYPE PWWN (VENDOR) FC4-TYPE:FEATURE
-----------------------------------------------------------------------
0xee0000 N 20:00:00:11:0d:97:00:00 scsi-fcp:init
0xee0001 N 20:00:00:11:0d:97:00:01 scsi-fcp:init
0xee0020 N 20:01:00:11:0d:97:01:00 scsi-fcp:target
0xee0021 N 20:01:00:11:0d:97:01:01 scsi-fcp:target
0xee0400 N 10:00:00:de:fb:74:e8:31 (Cisco) ipfc
Total number of entries = 5
Cisco MDS 9000 Series Fabric Configuration Guide, Release 8.x
51
Configuring and Managing Zones
Autozone Example Scenario

Cisco MDS 9000 Series Specifications

General

Category	Switch
Operating System	Cisco NX-OS
Ports	Varies by model
Protocols	Fibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
Redundancy	Redundant supervisors, power supplies, and fans
Management	Cisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization Support	VSANs (Virtual SANs)
Security Features	Fibre Channel Security Protocol (FC-SP)
Hot Swappable Components	power supplies, fans
Power Supply Options	AC and DC options available