Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual

TX1320 M1 Upgrade and Maintenance Manual
Contents
9.4.1.3 Network adapter D2745 . . . . . . . . . . . . . . . . . . . 203
9.4.1.4 Network adapter D2755 . . . . . . . . . . . . . . . . . . . 205
9.4.2 Handling SFP+ transceiver modules . . . . . . . . . . . . . . 207
9.4.2.1 Installing SFP+ transceiver modules . . . . . . . . . . . . . 207
9.4.2.2 Removing an SFP+ transceiver module . . . . . . . . . . . 212
9.4.2.3 Replacing SFP+ transceiver modules . . . . . . . . . . . . 214
10 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 215
10.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 216
10.1.1 Memory sequence . . . . . . . . . . . . . . . . . . . . . . . . 217
10.1.2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . 218
10.2 Removing memory modules . . . . . . . . . . . . . . . . . . 218
10.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 218
10.2.2 Removing a memory module . . . . . . . . . . . . . . . . . . 219
10.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 219
10.3 Installing memory modules . . . . . . . . . . . . . . . . . . 220
10.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 220
10.3.2 Installing a memory module . . . . . . . . . . . . . . . . . . . 220
10.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 221
10.4 Replacing memory modules . . . . . . . . . . . . . . . . . . 221
10.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 221
10.4.2 Removing the defective memory module . . . . . . . . . . . . 222
10.4.3 Installing the new memory module . . . . . . . . . . . . . . . 222
10.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 222
11 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
11.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 224
11.2 Upgrading or replacing the processor . . . . . . . . . . . . 224
11.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 224
11.2.2 Removing the processor heat sink . . . . . . . . . . . . . . . 225
11.2.3 Removing the processor . . . . . . . . . . . . . . . . . . . . . 226
11.2.4 Installing the processor . . . . . . . . . . . . . . . . . . . . . 227
11.2.5 Applying thermal paste . . . . . . . . . . . . . . . . . . . . . 229
11.2.6 Installing the processor heat sink . . . . . . . . . . . . . . . . 231
11.2.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 233

Fujitsu PRIMERGY TX1320 M1 Specifications

General

Processor Sockets	1
Memory Slots	4
Form Factor	Tower
Processor	Intel Celeron
Storage	Up to 4 x 3.5" or 2.5" drives
Drive Bays	4 x 3.5-inch or 8 x 2.5-inch
RAID Support	RAID 0, 1, 10
Network Controller	Dual-port Gigabit Ethernet
Operating System Support	Linux