Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual

Upgrade and Maintenance Manual TX1320 M1
Contents
9.2.1.4 Connecting cables to the expansion card . . . . . . . . . . 177
9.2.1.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 177
9.2.2 Removing expansion cards . . . . . . . . . . . . . . . . . . . 178
9.2.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 178
9.2.2.2 Removing an expansion card . . . . . . . . . . . . . . . . 179
9.2.2.3 Installing a PCI slot bracket . . . . . . . . . . . . . . . . . 180
9.2.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 180
9.2.3 Replacing expansion cards . . . . . . . . . . . . . . . . . . . 181
9.2.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 181
9.2.3.2 Removing an expansion card . . . . . . . . . . . . . . . . 182
9.2.3.3 Installing an expansion card . . . . . . . . . . . . . . . . . 182
9.2.3.4 Connecting cables to the expansion card . . . . . . . . . . 182
9.2.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 182
9.2.4 Replacing TFM . . . . . . . . . . . . . . . . . . . . . . . . . 184
9.2.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 184
9.2.4.2 Removing the defective TFM . . . . . . . . . . . . . . . . 184
9.2.4.3 Installing the new TFM . . . . . . . . . . . . . . . . . . . 185
9.2.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 185
9.3 Backup Units . . . . . . . . . . . . . . . . . . . . . . . . . . 186
9.3.1 Installing an FBU . . . . . . . . . . . . . . . . . . . . . . . . 186
9.3.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 186
9.3.1.2 Installing TFM to the RAID controller (if applicable) . . . . . 187
9.3.1.3 Preparing the FBU . . . . . . . . . . . . . . . . . . . . . 188
9.3.1.4 Installing the FBU holder into the chassis . . . . . . . . . . 189
9.3.1.5 Connecting the FBU adapter cable to the TFM . . . . . . . 190
9.3.1.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 191
9.3.2 Removing an FBU . . . . . . . . . . . . . . . . . . . . . . . 192
9.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 192
9.3.2.2 Disconnecting the FBU adapter cable from the TFM . . . . 193
9.3.2.3 Removing the FBU holder from the chassis . . . . . . . . . 193
9.3.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 194
9.3.3 Replacing an FBU . . . . . . . . . . . . . . . . . . . . . . . 195
9.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 195
9.3.3.2 Removing the FBU from the chassis . . . . . . . . . . . . 195
9.3.3.3 Removing the FBU from the FBU holder . . . . . . . . . . 196
9.3.3.4 Installing a replacement FBU . . . . . . . . . . . . . . . . 197
9.3.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 198
9.4 Additional tasks . . . . . . . . . . . . . . . . . . . . . . . . 199
9.4.1 Mounting expansion card slot brackets . . . . . . . . . . . . . 199
9.4.1.1 General instructions . . . . . . . . . . . . . . . . . . . . . 200
9.4.1.2 Network adapter D2735 . . . . . . . . . . . . . . . . . . . 201

Fujitsu PRIMERGY TX1320 M1 Specifications

General

Processor Sockets	1
Memory Slots	4
Form Factor	Tower
Processor	Intel Celeron
Storage	Up to 4 x 3.5" or 2.5" drives
Drive Bays	4 x 3.5-inch or 8 x 2.5-inch
RAID Support	RAID 0, 1, 10
Network Controller	Dual-port Gigabit Ethernet
Operating System Support	Linux