EasyManuals Logo

Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual

Fujitsu PRIMERGY TX1320 M1
340 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
TX1320 M1
Upgrade and Maintenance Manual
Contents
5.2.2 Verifying system information backup / restore . . . . . . . . . . 86
5.2.3 Updating RAID controller firmware . . . . . . . . . . . . . . . 87
5.2.4 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . 88
5.2.5 Verifying and configuring the backup software solution . . . . . 89
5.2.6 Resetting the boot retry counter . . . . . . . . . . . . . . . . . 90
5.2.6.1 Viewing the boot retry counter . . . . . . . . . . . . . . . . 90
5.2.6.2 Resetting the boot retry counter . . . . . . . . . . . . . . . 90
5.2.7 Enabling SVOM boot watchdog functionality . . . . . . . . . . 92
5.2.8 Enabling replaced components in the system BIOS . . . . . . . 92
5.2.9 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 94
5.2.10 Verifying the system time settings . . . . . . . . . . . . . . . . 95
5.2.11 Viewing and clearing the System Event Log (SEL) . . . . . . . 96
5.2.11.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 96
5.2.11.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 97
5.2.12 Updating the NIC configuration file in a Linux environment . . . 97
5.2.13 Enabling BitLocker functionality . . . . . . . . . . . . . . . . . 99
5.2.14 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 100
5.2.15 Looking up changed MAC / WWN addresses . . . . . . . . . . 100
5.2.15.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 100
5.2.15.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 101
5.2.16 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 102
5.2.17 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 102
5.2.17.1 After replacing / upgrading LAN controllers . . . . . . . . . 103
5.2.17.2 After replacing the system board . . . . . . . . . . . . . . . 103
5.2.18 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 103
5.2.19 Performing a fan test after replacing a defective fan . . . . . . 104
6 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 107
6.1 Standard power supply unit . . . . . . . . . . . . . . . . . . 108
6.1.1 Replacing the standard power supply unit . . . . . . . . . . . . 108
6.1.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 108
6.1.1.2 Disconnecting internal power cables . . . . . . . . . . . . . 109
6.1.1.3 Removing the PSU . . . . . . . . . . . . . . . . . . . . . . 110
6.1.1.4 Installing the PSU . . . . . . . . . . . . . . . . . . . . . . 111
6.1.1.5 Reconnecting internal power cables . . . . . . . . . . . . . 113
6.1.1.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 114

Table of Contents

Other manuals for Fujitsu PRIMERGY TX1320 M1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY TX1320 M1 and is the answer not in the manual?

Fujitsu PRIMERGY TX1320 M1 Specifications

General IconGeneral
Processor Sockets1
Memory Slots4
Form FactorTower
ProcessorIntel Celeron
StorageUp to 4 x 3.5" or 2.5" drives
Drive Bays4 x 3.5-inch or 8 x 2.5-inch
RAID SupportRAID 0, 1, 10
Network ControllerDual-port Gigabit Ethernet
Operating System SupportLinux

Related product manuals