Fujitsu PRIMERGY TX1320 M1 Upgrade And Maintenance Manual

Upgrade and Maintenance Manual TX1320 M1
Contents
7 Hard disk drives / solid state drives . . . . . . . . . . . . . 115
7.1 Basic procedure . . . . . . . . . . . . . . . . . . . . . . . . 116
7.2 2.5-inch hard disk drives / solid state drives . . . . . . . . 117
7.2.1 Mounting order for 2.5-inch HDDs / SSDs . . . . . . . . . . . 117
7.2.1.1 HDD/SSD naming scheme . . . . . . . . . . . . . . . . . 117
7.2.2 Installing 2.5-inch HDD / SSD modules . . . . . . . . . . . . . 118
7.2.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 118
7.2.2.2 Removing a 2.5-inch HDD / SSD dummy module . . . . . 119
7.2.2.3 Installing a 2.5-inch HDD / SSD module . . . . . . . . . . 120
7.2.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 121
7.2.3 Removing 2.5-inch HDD / SSD modules . . . . . . . . . . . . 122
7.2.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 122
7.2.3.2 Removing a 2.5-inch HDD / SSD module . . . . . . . . . . 123
7.2.3.3 Installing a 2.5-inch HDD / SSD dummy module . . . . . . 125
7.2.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 125
7.2.4 Replacing a 2.5-inch HDD / SSD module . . . . . . . . . . . . 126
7.2.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 126
7.2.4.2 Removing a 2.5-inch HDD / SSD module . . . . . . . . . . 127
7.2.4.3 Installing a 2.5-inch HDD / SSD module . . . . . . . . . . 127
7.2.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 127
7.3 3.5-inch hard disk drives . . . . . . . . . . . . . . . . . . . 128
7.3.1 Mounting order for 3.5-inch HDDs . . . . . . . . . . . . . . . 128
7.3.2 Installing 3.5-inch HDD modules . . . . . . . . . . . . . . . . 129
7.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 129
7.3.2.2 Installing a 3.5-inch HDD module . . . . . . . . . . . . . . 130
7.3.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 133
7.3.3 Removing 3.5-inch HDD modules . . . . . . . . . . . . . . . 134
7.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 134
7.3.3.2 Removing a 3.5-inch HDD module . . . . . . . . . . . . . 135
7.3.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 137
7.3.4 Replacing a 3.5-inch HDD module . . . . . . . . . . . . . . . 137
7.3.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 138
7.3.4.2 Removing a 3.5-inch HDD module . . . . . . . . . . . . . 138
7.3.4.3 Installing a 3.5-inch HDD module . . . . . . . . . . . . . . 139
7.3.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 139
7.4 Replacing SAS / SATA backplane . . . . . . . . . . . . . . 140
7.4.1 Replacing 2.5- inch SAS / SATA backplane . . . . . . . . . . 140
7.4.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 140
7.4.1.2 Removing the air duct (if applicable) . . . . . . . . . . . . 142

Fujitsu PRIMERGY TX1320 M1 Specifications

General

Processor Sockets	1
Memory Slots	4
Form Factor	Tower
Processor	Intel Celeron
Storage	Up to 4 x 3.5" or 2.5" drives
Drive Bays	4 x 3.5-inch or 8 x 2.5-inch
RAID Support	RAID 0, 1, 10
Network Controller	Dual-port Gigabit Ethernet
Operating System Support	Linux