Combination mode
188
Detune BPM Adjust
Detune BPM Adjust is available on the Pitch tab of the
Timbre Parameters page.
This command changes a loop’s tempo by changing the
Timbre’s Detune parameter. The sample data itself is not
altered. Since this alters the pitch of the loop along with the
tempo, it’s generally suited only to un-pitched percussive
loops.
Note: Using Detune BPM Adjust will over-write any
previous Detune settings.
1. Go to the Pitch tab of the Timbre Parameters page.
2. Select the Detune parameter for the desired Timbre.
Detune BPM Adjust is available only when the Detune
parameter has been selected. Otherwise, the menu selection
will be grayed out.
3. Select “Detune BPM Adjust” to open the dialog box.
4. In From, specify the loop’s original BPM value.
Ignore any previous changes from using Detune BPM
adjust.
5. In To, specify the desired BPM value.
The appropriate Detune value will be calculated
automatically from these two values.
For example, if you set From to 60 bpm and To to 120 bpm,
Detune will be set to +1200 (one octave up).
6. To execute the Detune BPM Adjust command, press the
OK button. To exit without changing the Detune value,
press the Cancel button.
Note: Since this command does not affect the sample data
itself, and always over-writes the previous Detune amount,
using it repeatedly has no cumulative effect.
Copy KARMA Module
This command copies the settings of the KARMA Module
used by a specified program, combination, or song.
1. Select “Copy KARMA Module” to open the dialog box.
2. In From, select the copy source mode, bank, and
number.
You can press a BANK SELECT I-A–U-G switch to select
the bank.
3. If you selected a combination or song as the copy-
source, select the module from which you want to copy.
4. As appropriate for the content that you want to copy,
turn “GE RTP Control & Scenes” On (checked). (see
“Settings copied by Copy KARMA Module”)
5. If you want to copy performance realtime parameters,
Dynamic MIDI, and front panel settings, turn “Perf.
RTP & Panel Settings” On (checked). (see “Settings
copied by Copy KARMA Module”)
6. If you also want to copy the note and velocity settings
of pads 1–8, turn “Pads” On (checked).
7. Use the To field to select the copy-destination KARMA
module.
8. Press the OK button to execute the Copy KARMA
Module command, or press the Cancel button if you
decide to cancel.
Settings copied by “Copy KARMA Module”
When copying from a program
If GE RTP Control & Scenes and Perf. RTP & Panel
Settings are Off (checked), the following content is copied.
• The GE selected by the copy-source KARMA module.
• Link to DT setting.
• Settings of the KARMA module parameters (7–1:
KARMA1– Trigger, 7–1: KARMA1– Control).
• 7–2: KARMA2– GE RTP MIN, MAX, and VALUE
settings.
If you turn “GE RTP Control & Scenes” On (checked)
In addition to the content copied when “GE RTP Control &
Scenes” is Off (unchecked), the following content is copied.
• 7–2: KARMA2– GE RTP ASSIGN and POL. settings.
• The scene selected in the master buffer (A), the KARMA
Slider and KARMA Switch settings of each scene (0:
Play– KARMA RTC and 0: Play– Control Surface
“KARMA” settings).
• 7–2: KARMA2– Names controller name settings.
If you turn “Perf. RTP & Panel Setting” On (checked)
In addition to the content copied when “Perf. RTP & Panel
Settings” is Off (unchecked), the following content is copied.
• Tempo setting.
• Time Signature setting.
• KARMA ON/OFF switch setting.
• KARMA LATCH switch setting.
• 7–1: KARMA1– Drum Track Control page settings.
• 7–2: KARMA2– Perf RTP page settings.
• 7–2: KARMA2– Dynamic MIDI page settings.
When copying from a combination or song
If GE RTP Control & Scenes and Perf. RTP & Panel
Settings are Off (unchecked) when you copy from a
combination or song, the following content is copied.
• The GE selected for the copy-destination KARMA
module (including the GE realtime parameters).
• Link to DT setting of the copy-source KARMA module.
• KARMA module parameters (7–2: KARMA2– Trigger,
7–2: KARMA2– Control).
• 7–3: KARMA3– GE RTP MIN, MAX, and VALUE
settings.
If you turn “GE RTP Control & Scenes” On (checked)
In addition to the content copied when GE RTP Control &
Scenes is Off (unchecked), the following content is copied.
• 7–3: KARMA3– GE RTP page ASSIGN and POL.
settings.
• The KARMA CONTROLS slider and KARMA SWITCH
settings of each scene in the copy-source buffer, and the
currently selected scene.
To Next Page
Loading...
Need help?
General
