Lupus Electronics XT 1 Plus - Sensor Firmware Management; Sensor Software Version Check

332 pages

Save Page as PDF

To Next Page

To Previous Page

127

Sensor firmware

In case it is necessary to update the sensor firmware, it can be done in this menu.

Sensor software

This menu shows you the software version of your sensors. It is not possible to install

an update.

Main Page

Table of Contents2
Table of Content2
Introduction7
- Difference of the Alarm Panels8
- Disclaimer9
- Important Safety Information11
- If You Find Defects12
- Designated Use12
The most Important Chapters for the Initial Setup13
Putting the LUPUSEC-XT2 (Plus) into Operation14
- Place of Installation14
- Connecting the XT1 Plus Alarm Panel15
- Connecting the XT2 (Plus) Alarm Panel17
- Connecting the XT3 Alarm Panel19
- Additional Mounting Information23
Description of the Leds24
Access to the Web Interface of the LUPUSEC-XT Alarm Panel27
User Interface of the Alarm Panel33
- Home Menu38
- Configure Overview Page42
- Sensors46
- List47
- Edit Sensor50
- Add54
- Range55
- Universal Remote Control56
- Smart Home Menu58
- Automation58
- Home Automation Settings62
- Condition62
- Schedule64
- Action65
- Examples68
- Wireless Plugs76
- Cameras81
- Capture84
- Power Consumption85
- Temperature History86
- Scenarios87
- Alarm System88
- Settings88
- Siren Settings95
- Report100
- PIN Codes105
Settings107
- Network107
- E-Mail Account110
- SMS Account112
- SIM Card114
- Device Integration117
- System Menu120
- Status120
- Logs122
- Password123
- Firmware125
Factory Reset128
- Logout129
Remote Access Via the Internet130
- Ipv4 / Ipv6 Problem130
- Port Forwarding131
  - Port Forwarding - Brief Instructions (Currently Only in German)131
- Access Via the LUPUS App (for Android + Ios)132
  - Profile List140
  - Usage of the Alarm Panel App141
Alarm Test146
Description of Sensors and Controls147
Overview of Sensors Compatibility148
- The Internal I/O Terminal of the XT3151
- Integration of Lamps of Other Manufacturers153
- 12 / 24 V Wireless Relay156
- Connecting the 12 / 24 V Wireless Relay and Putting It into Operation157
Channel Relay159
- Connecting the Single Channel Relay and Putting It into Operation160
Channel Relay162
- Connecting the Double Channel Relay and Putting It into Operation163
360° PIR Motion Detector165
- Connecting the 360° PIR Motion Detector and Putting It into Operation166
CO Detector168
- Connecting the CO Detector and Putting It into Operation168
Curtain Motion Detector170
- Connecting the Curtain Motion Detector and Putting It into Operation171
Door Contact174
- Connecting the Door Contact and Putting It into Operation175
Door Contact V2177
- Connecting the Door Contact V2 and Putting It into Operation178
Dual-Way Motion Detector181
- Connecting the PIR / Microwave Motion Detector and Putting It into Operation182
Electric Meter185
- Connecting the Electric Meter and Putting It into Operation186
Emergency Button189
- Connecting the Emergency Button and Putting It into Operation190
Glass Breaking Sensor192
- Connecting the Glass Breaking Sensor and Putting It into Operation192
Glass Breaking Sensor V2195
- Connecting the Glass Breaking Sensor V2 and Putting It into Operation196
Heat Detector198
- Connecting the Heat Detector and Putting It into Operation198
Indoor Siren200
- Connecting the Indoor Siren and Putting It into Operation200
Keypad206
- Connecting the Keypad and Putting It into Operation207
Light Sensor211
- Connecting the Light Sensor and Putting It into Operation212
Light Switch V2214
- Installation of Light Switch V2215
Lockswitch Contact219
- Connecting the Lockswitch Contact and Putting It into Operation220
Magnetic Lock222
- Installing the Magnetic Lock to the Door and Putting It into Operation223
Mechanical Lock224
- Installing the Mechanical Lock to the Doorframe and Putting It into Operation225
Medical Emergency Controller227
- Connecting the Medical Emergency Controller and Putting It into Operation227
Outdoor Keypad229
- Connecting the Outdoor Keypad with Tag Reader and Putting It into Operation231
Outdoor Siren V2239
- Connecting the Outdoor Siren V2 and Putting It into Operation240
Panic Button245
- Connecting the Panic Button and Putting It into Operation245
PIR Motion Detector V2246
- Connecting the PIR Motion Detector V2 and Putting It into Operation247
PIR Network Camera V3250
- Connecting the PIR Network Camera V3 und Putting It into Operation251
Radiator Valve Thermostat V2254
- Installation of Radiator Valve Thermostat V2256
Relay with Power Meter V2260
- Connecting Relay with Power Meter for XT2 Plus and Putting It into Operation261
Remote Control V2263
- Connecting the Remote Control V2 and Putting It into Operation264
Remote Controlled Mains Socket with Power Meter and Zigbee Repeater265
- Connecting the Wireless Socket and Putting It into Operation266
Scenario Switch V2268
- Connecting the Scenario Switch V2 and Putting It into Operation269
Sensor Input271
- Connecting the Sensor Input and Putting It into Operation272
Sensor Input (9 Fold)274
- Calibrating the Sensor Input (9 Fold)276
Shutter Relay V2278
- Connecting the Shutter Relay V2 and Putting It into Operation281
Small Indoor Siren V2284
- Connecting the Small Indoor Siren and Putting It into Operation285
Smoke Detector V2287
- Connecting the Smoke Detector V2 and Putting It into Operation289
Status Display292
- Connecting the Status Display and Putting It into Operation293
Tag Reader V2295
- Connecting the Tag Reader V2 and Putting It into Operation296
Temperature Sensor V2298
- Connecting the Temperature Sensor and Putting It into Operation298
Temperature Sensor with Display V2300
- Connecting the Temperature Sensor and Putting It into Operation300
Temperature Sensor with External Probe302
- Connecting the Temperature Sensor with External Probe and Putting It into Operation303
Top-Hat Rail Relay304
- Connecting the Top-Hat Rail Relay and Putting It into Operation305
Universal IR Controller307
- Connecting the Universal IR Controller and Putting It into Operation308
- Learn and Test IR Signals308
- Installation311
- IR LED Selection and Operation312
Upgrade Dongle to XT2 Plus313
Vibration Sensor314
- Connecting the Vibration Sensor and Putting It into Operation315
Water Sensor317
- Connecting the Water Sensor and Putting It into Operation317
Water Sensor V2319
- Connecting the Water Sensor V2 and Putting It into Operation320
Wireless Relay322
- Connecting the Wireless Relay and Putting It into Operation322
Wireless Repeater V2324
- Connecting the Wireless Repeater V2 and Putting It into Operation325

Lupus Electronics XT 1 Plus - Sensor Firmware Management; Sensor Software Version Check

Table of Contents