Lenze i950

v
t
Source TP 2
(0x5020:012)
v
t
v
max
Mark window size tool (0x5041:126)
Mark window offset tool (0x5041:127)
Max missed marks tool (0x5041:128)
Sensor distance
(0x5041:120)
-
Sensor set position
(0x5042:140)
+
Tool Sensor act position
(0x5042:141)
v
t
v
max
Max positive correction tool (0x5041:122)
Max negative correction tool (0x5041:123)
DI 1
DI 2
DI 3
DI 4
TP calculation Mark window Mark stack
Upper correction position tool (0x5041:124)
Lower correction position tool (0x5041:125)
SetPosition
relative
Tool Correction
Tool correction
(0x5041:120)
Actual tool error
(0x5042:142)
Actual tool error limited
(0x5042:143)
Fig. 65: Tool correcon
paral signal ow
Relevant parameters of other funcons
Address Designaon Default seng Seng range
0x500B:031 Cycle length 360.0000 0.0001 ... 214748.3647
0x500C:186 Deceleraon of Halt 1800.00 0.00 ... 21474836.47
0x5020:011 TP1 source Digital input 1, posive edge [1] Selecon list
0x5020:014 Master value source System bus [0] Selecon list
0x5021:151 System bus
diagnoscs: Posion (input value) - (Read only)
0x5041:002 Mark distance 360.0000 0.0000 ... 214748.3647
0x5041:003 Max. posive correcon 45.0000 0.0000 ... 214748.3647
0x5041:004 Max. negave correcon 45.0000 0.0000 ... 214748.3647
0x5041:005 Reference measuring system of correcon window Corrected master posion [1] Selecon list
0x5041:006 Upper correcon posion 350.0000 0.0000 ... 214748.3647
0x5041:007 Lower correcon posion 200.0000 0.0000 ... 214748.3647
0x5041:008 Mark window size 40.0000 0.0000 ... 214748.3647
0x5041:009 Mark window oset 0.0000 0.0000 ... 214748.3647
0x5041:010 Max. number of missed marks 20 0 ... 4294967295
0x5041:011 Gearbox factor correcon gain 0.1000 0.0000 ... 214748.3647
0x5041:012 Max. gearbox factor correcon 10.0000 0.0000 ... 214748.3647
0x5042:001 Sensor set posion - (Read only)
0x5042:002 Actual mark posion - (Read only)
0x5042:003 Actual mark error - (Read only)
0x5042:004 Actual limited mark error - (Read only)
0x5042:005 Actual gearbox factor - (Read only)
0x5042:006 Corrected set posion - (Read only)
0x5042:007 Corrected set velocity - (Read only)
0x5042:016 Set posion of selected master value - (Read only)
0x5042:017 Set velocity of selected master value - (Read only)
0x5046:001 Virtual master start
posion 0.0000 0.0000 ... 214748.3647
0x5046:002 Virtual master set posion 0.0000 0.0000 ... 214748.3647
0x5046:003 Virtual master acceleraon 100000.00 0.00 ... 21474836.47
Conguring the "Sync and Correcon" TA
Signal ow
Master value selecon and master value correcon
150