MacDon PW8 - Page 11

215575 vii Revision B
4.3.1 Removing Header Height Sensor Assembly — Left Side..................................................................... 105
4.3.2 Installing Header Height Sensor Assembly — Left Side ...................................................................... 106
4.3.3 Removing Header Height Control System — Right Side ..................................................................... 107
4.3.4 Installing Header Height Sensor Assembly — Right Side .................................................................... 109
4.4 Height Sensor Output Voltage Range – Combine Requirements .................................................................. 111
4.4.1 Manually Checking Voltage Range................................................................................................. 111
4.4.2 Adjusting Header Height Sensor Voltage Range – Left Side ................................................................ 114
4.4.3 Adjusting Header Height Sensor Voltage Range – Right Side .............................................................. 114
4.5 IDEAL
™
Series Combines ...................................................................................................................... 117
4.5.1 Setting up the Header – IDEAL
™
Series .......................................................................................... 117
4.5.2 Setting up Automatic Header Controls – IDEAL
™
Series..................................................................... 122
4.5.3 Calibrating the Header – IDEAL
™
Series.......................................................................................... 123
4.5.4 Operating the Header – IDEAL
™
Series........................................................................................... 125
4.5.5 Reviewing Header In-Field Settings – IDEAL
™
Series ......................................................................... 127
4.6 Case IH 5130/6130/7130 and 5140/6140/7140 Midrange Combines............................................................ 129
4.6.1 Setting up the Header on the Combine Display (Case IH 5130/6130/7130; 5140/6140/7140) .................. 129
4.6.2 Checking Voltage Range from Combine Cab (Case IH 5130/6130/7130; 5140/6140/7140)....................... 130
4.6.3 Calibrating Auto Header Height Control (Case IH 5130/6130/7130; 5140/6140/7140) ............................ 132
4.6.4 Setting Preset Cutting Height (Case IH 5130/6130/7130; 5140/6140/7140) .......................................... 133
4.7 Case IH 7010/8010, 7120/8120/9120, 7230/8230/9230, and 7240/8240/9240 Combines................................ 136
4.7.1 Checking Voltage Range from Combine Cab (Case 8010) ................................................................... 136
4.7.2 Checking Voltage Range from Combine Cab (Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240)....................................................................................................................... 138
4.7.3 Calibrating Auto Header Height Control (Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240) – Software Versions Below 28.00 ......................................................................... 139
4.7.4 Calibrating Auto Header Height Control (Case IH 7010/8010; 7120/8120/9120; 7230/8230/9230;
7240/8240/9240) – Software Versions Above 28.00 ......................................................................... 141
4.7.5 Setting Preset Cutting Height (Case 7010/8010, 7120/8120/9120, 7230/8230/9230,
7240/8240/9240)....................................................................................................................... 143
4.8 Challenger
®
6 Combines ...................................................................................................................... 145
4.8.1 Checking Voltage Range from Combine Cab – Challenger
®
6 and 7 Series ............................................ 145
4.8.2 Engaging Auto Header Height Control – Challenger
®
6 Series............................................................. 146
4.8.3 Calibrating Auto Header Height Control – Challenger
®
6 Series .......................................................... 147
4.8.4 Adjusting Header Height – Challenger
®
6 Series............................................................................... 149
4.8.5 Adjusting Header Raise/Lower Rate – Challenger
®
6 Series................................................................ 149
4.8.6 Setting Sensitivity of Auto Header Height Control – Challenger
®
6 Series ............................................. 151
4.9 Gleaner
®
R65/R66/R75/R76 and S Series Combines – Except S9 Series......................................................... 152
4.9.1 Checking Voltage Range from Combine Cab – Gleaner
®
R65/R66/R75/R76 and S Series ......................... 152
4.9.2 Engaging Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series ................................. 153
4.9.3 Calibrating Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series ............................... 154
4.9.4 Turning Accumulator Off – Gleaner
®
R65/R66/R75/R76 and S Series................................................... 156
4.9.5 Adjusting Header Raise/Lower Rate – Gleaner
®
R65/R66/R75/R76 and S Series .................................... 156
4.9.6 Adjusting Ground Pressure – Gleaner
®
R65/R66/R75/R76 and S Series ................................................ 157
4.9.7 Adjusting Sensitivity of Auto Header Height Control – Gleaner
®
R65/R66/R75/R76 and S Series............... 158
TABLE OF CONTENTS