215575 viii Revision B
4.9.8 Troubleshooting Alarms and Diagnostic Faults – Gleaner
®
R65/R66/R75/R76 and S Series ...................... 159
4.10 Gleaner
®
S9 Series Combines .............................................................................................................. 161
4.10.1 Setting up the Header – Gleaner
®
S9 Series .................................................................................. 161
4.10.2 Setting up Automatic Header Controls – Gleaner
®
S9 Series............................................................. 165
4.10.3 Calibrating Header – Gleaner
®
S9 Series ....................................................................................... 167
4.10.4 Operating with a Gleaner
®
S9 Series Combine ............................................................................... 171
4.10.5 Header In-Field Settings for Gleaner
®
S9 Series Combine................................................................. 172
4.11 John Deere 60 Series Combines........................................................................................................... 175
4.11.1 Checking Voltage Range from Combine Cab (John Deere 60 Series)................................................... 175
4.11.2 Calibrating Auto Header Height Control (John Deere 60 Series) ........................................................ 176
4.11.3 Turning Off Accumulator (John Deere 60 Series) ............................................................................ 177
4.11.4 Setting Sensing Grain Header Height (John Deere 60 Series) ............................................................ 178
4.11.5 Setting Sensitivity of Auto Header Height Control (John Deere 60 Series) ........................................... 179
4.11.6 Adjusting Threshold for Drop Rate Valve (John Deere 60 Series) ....................................................... 180
4.12 John Deere 70 Series Combines........................................................................................................... 181
4.12.1 Checking Voltage Range from Combine Cab (John Deere 70 Series)................................................... 181
4.12.2 Calibrating Feeder House Speed (John Deere 70 Series) .................................................................. 183
4.12.3 Calibrating Auto Header Height Control (John Deere 70 Series) ........................................................ 183
4.12.4 Setting Sensitivity of Auto Header Height Control (John Deere 70 Series) ........................................... 185
4.12.5 Adjusting Manual Header Raise/Lower Rate (John Deere 70 Series) .................................................. 185
4.13 John Deere S and T Series Combines .................................................................................................... 187
4.13.1 Checking Voltage Range from Combine Cab (John Deere S and T Series) ............................................ 187
4.13.2 Calibrating Feeder House Fore-Aft Tilt Range (John Deere S and T Series)........................................... 189
4.13.3 Calibrating Auto Header Height Control (John Deere S and T Series).................................................. 191
4.13.4 Setting Sensitivity of Auto Header Height Control (John Deere S and T Series)..................................... 193
4.13.5 Adjusting Manual Header Raise/Lower Rate (John Deere S and T Series) ............................................ 194
4.13.6 Setting Preset Cutting Height (John Deere S and T Series)................................................................ 195
4.14 New Holland Combines CX/CR Series (CR Series – Model Year 2014 and Earlier) .......................................... 198
4.14.1 Checking Voltage Range from Combine Cab (New Holland CX/CR Series)............................................ 198
4.14.2 Engaging Auto Header Height Control (New Holland CR/CX Series).................................................... 200
4.14.3 Calibrating Auto Header Height Control (New Holland CR/CX Series) ................................................. 200
Calibrating Maximum Stubble Height ........................................................................................... 202
4.14.4 Adjusting Header Raise Rate (New Holland CR/CX Series) ................................................................ 203
4.14.5 Setting Header Lower Rate (New Holland CR/CX Series) .................................................................. 203
4.14.6 Setting Auto Header Height Control Sensitivity to 200 (New Holland CR/CX Series) .............................. 204
4.14.7 Setting Preset Cutting Height (New Holland CR/CX Series) ............................................................... 204
4.15 New Holland Combines (CR Series – Model Year 2015 and Later) .............................................................. 206
4.15.1 Engaging Auto Header Height Control (New Holland CR Series) ........................................................ 206
4.15.2 Checking Voltage Range from Combine Cab (New Holland CR Series) ................................................ 208
4.15.3 Calibrating Auto Header Height Control (New Holland CR Series) ...................................................... 210
4.15.4 Setting Auto Height (New Holland CR Series)................................................................................. 212
4.15.5 Setting Maximum Work Height (New Holland CR Series) ................................................................. 213
TABLE OF CONTENTS
To Next Page
Loading...
