Rohde & Schwarz CMU 200 - Page 359

CMU List of Commands
1100.4903.12 6.93 E-10
Command Parameters Remarks Page
CONFigure:POWer:CONTrol:REPetition CONTinuous | SINGleshot | 1
to 10000, NONE,STEP |
NONE
with query 6.45
CONFigure:POWer:EREPorting SRQ | SOPC | SRSQ | OFF with query 6.44
[SENSe:]POWer:FREQuency:BANDwidth[:RESolution] 10 Hz to 1 MHz with query 6.46
[SENSe:]POWer:FREQuency:BWIDth[:RESolution] 10 Hz to 1 MHz with query 6.46
[SENSe:]POWer:FREQuency:CENTer 10 kHz to 2.7 GHz with query 6.46
[SENSe:]POWer:LEVel:RANGe 10.0 dB to 100.0 dB with query 6.46
READ:ARRay:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.49
FETCh:ARRay:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.49
SAMPle:ARRay:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.49
READ:SUBarrays:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.50
FETCh:SUBarrays:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.50
SAMPle:SUBarrays:POWer:MAXimum? –128.0 dBm to +48.0 dBm query only 6.50
READ:ARRay:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.49
READ:ARRay:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.49
FETCh:ARRay:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.49
FETCh:ARRay:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.49
SAMPle:ARRay:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.49
READ:SUBarrays:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.50
READ:SUBarrays:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.50
FETCh:SUBarrays:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.50
FETCh:SUBarrays:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.50
SAMPle:SUBarrays:POWer:MINimum? –128.0 dBm to +48.0 dBm query only 6.50
FETCh:POWer:STATus? OFF | RUN | STOP | ERR |
STEP | RDY, 0 to 10000 |
NONE , 0 to 1000 | NONE
query only 6.44
[SENSe:]POWer:TIME:DELay -1000.0 µs to +1000.0 µs depending on
span and
bandwidth
6.47
[SENSe:]POWer:TIME:SPAN 10 µs to 10 s depending on
bandwidth
6.47
READ:ARRay:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.49
FETCh:ARRay:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.49
SAMPle:ARRay:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.49
READ:SUBarrays:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.50
FETCh:SUBarrays:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.50
SAMPle:SUBarrays:POWer[:CURRent]? –128.0 dBm to +48.0 dBm query only 6.50
Subsystem OPTions (options)
SYSTem:OPTions:INFO:CURRent? query only 6.25
Save/Recall of settings
MMEMory:RECall:CURRent <FileName> [,<msus>] no query 6.26
MMEMory:SAVE:CURRent <FileName> [,<msus>] no query 6.25
Partial reset
SYSTem:RESet:CURRent – no query 6.26
Test object RFANalyzer (Power)
INITiate:RFANalyzer – no query 6.30