Rohde & Schwarz CMU 200 User Manual

List of Commands CMU
1100.4903.12 6.94 E-10
Command Parameters Remarks Page
ABORt:RFANalyzer – no query 6.30
STOP:RFANalyzer – no query 6.30
CONTinue:RFANalyzer – no query 6.30
[SENSe:]RFANalyzer:BANDwidth[:RESolution] 10 Hz to 1 MHz | WIDE with query 6.30
[SENSe:]RFANalyzer:BWIDth[:RESolution] 10 Hz to 1MHz | WIDE with query 6.30
CONFigure:RFANalyzer:CONTrol:REPetition CONTinuous | SINGleshot | 1
to 10000, NONE,STEP |
NONE
with query 6.32
CONFigure:RFANalyzer:EREPorting SRQ | SOPC | SRSQ | OFF with query 6.31
[SENSe:]RFANalyzer:FREQuency 100 kHz to 2.7 GHz with query 6.30
CONFigure:RFANalyzer:POWer:RTIMe 0 to xxx with query 6.32
READ[:SCALar]:RFANalyzer:POWer? -120.0 dBm to +47.0 dBm query only 6.32
FETCh[:SCALar]:RFANalyzer:POWer? -120.0 dBm to +47.0 dBm query only 6.32
SAMPle[:SCALar]:RFANalyzer:POWer? -120.0 dBm to +47.0 dBm query only 6.32
FETCh:RFANalyzer:STATus? OFF | RUN | STOP | ERR |
STEP | RDY, 0 to 10000 |
NONE , 0 to 1000 | NONE
query only 6.31
Generator object RFGenerator
DEFault:RFGenerator ON | OFF with query 6.33
INITiate:RFGenerator – no query 6.33
ABORt:RFGenerator – no query 6.33
CONFigure:RFGenerator:APPLication TX | AUXT | TXAT with query 6.33
DEFault:RFGenerator:AUXTx ON | OFF with query 6.38
SOURce:RFGenerator:AUXTx: FREQuency 350 MHz to 550 MHz | 700
MHz to 1100 MHz | 1400 MHz
to 2200 MHz
with query 6.38
SOURce:RFGenerator:AUXTx:LEVel -137.0 dBm to + 13.0 dBm restricted for
RF1 / 2
6.38
SOURce:RFGenerator:BANDwidth OFF | F30Khz | F300khz with query 6.37
SOURce:RFGenerator:BWIDth <Bandwidth> with query 6.37
SOURce:RFGenerator:FHOPping:FREQuency 100.0 kHz to 2.7 GHz with query 6.36
SOURce:RFGenerator:FHOPping:FREQuency:MODE ABSolute | RELative with query 6.36
SOURce:RFGenerator:FHOPping:STATe OFF | ON with query 6.36
SOURce:RFGenerator:MODulation OFF | SSB | AM with query 6.35
SOURce:RFGenerator:MODulation:SSB:FREQuency -300 kHz to +300 kHz with query 6.35
SOURce:RFGenerator:MODulation[:AM]:INDex 0% to 100% with query 6.35
SOURce:RFGenerator:PULSe:STATe OFF | ON with query 6.37
FETCh:RFGenerator:STATus? OFF | RUN | ERR query only 6.34
DEFault:RFGenerator:TX ON | OFF with query 6.33
SOURce:RFGenerator[:TX]:FREQuency 100.0 kHz to 2.7 GHz with query 6.34
SOURce:RFGenerator[:TX]:LEVel -137.0 dBm to + 13.0 dBm restricted for
RF1 / 2
6.34
Test object SPECtrum
INITiate:SPECtrum – no query 6.51
ABORt:SPECtrum – no query 6.51
STOP:SPECtrum – no query 6.51
CONTinue:SPECtrum – no query 6.51
CONFigure:SUBarrays:SPECtrum ALL | ARIThmetical | MINimum with query 6.54

Rohde & Schwarz CMU 200 Specifications

General

Brand	Rohde & Schwarz
Model	CMU 200
Category	Test Equipment
Language	English