Yamaha F150A - Index

i-1
Index
A.
Abbreviation ................................................0-5
Adjusting the forward gear shim
thickness (T1) .........................................8-41
Adjusting the forward gear shim
thickness (T2) .........................................8-74
Adjusting the reverse gear shim
thickness (T1) .........................................8-76
Adjusting the reverse gear shim
thickness (T2) .........................................8-43
Adjusting the shift link/shift cable ............10-15
Adjusting the throttle link...........................6-27
Adjusting the throttle link/throttle cable/throttle
pick-up timing........................................10-15
Adjusting the TPS .....................................6-27
Adjusting the trim sensor cam...................9-32
Adjusting the valve clearance .....................7-3
After test run .............................................10-8
Air hose, pressure regulator hose, and vapor
gas hose ...................................................6-2
Assembling the cylinder block...................7-75
Assembling the cylinder head ...................7-45
Assembling the drive shaft
housing ..........................................8-23, 8-64
Assembling the forward gear ....................8-23
Assembling the fuel filter assembly.............6-9
Assembling the fuel pump assembly ........6-14
Assembling the gear pump .......................9-59
Assembling the gear pump housing..........9-60
Assembling the lower case ..............8-24, 8-63
Assembling the oil pan and
exhaust manifold.....................................9-22
Assembling the oil pump..................7-54, 7-60
Assembling the propeller
(SDS propeller) ............... 8-4, 8-8, 8-47, 8-50
Assembling the propeller shaft
assembly.................................................8-17
Assembling the propeller shaft housing
assembly.................................................8-17
Assembling the propeller shaft housing
assembly and forward gear.....................8-57
Assembling the PTT motor .......................9-52
Assembling the reverse gear ....................8-63
Assembling the shift bracket .......................9-3
Assembling the starter motor ....................5-38
Assembling the tilt ram..............................9-44
Assembling the trim ram ...........................9-45
Assembling the upper case.......................9-18
Assembling the vapor separator ...............6-44
Assembling the water pump housing ........8-12
Assembling the water pump
housing ...................................................8-53
B.
Basic components ...................................... 4-1
Battery installation .................................... 3-22
Battery wiring with house (accessory)
battery..................................................... 3-25
Battery wiring without house (accessory)
battery..................................................... 3-22
Bleeding the PTT unit ............................... 9-37
Blowby hose and cooling water hose ......... 6-4
Bottom cowling .................................. 5-7, 9-11
Bracket unit............................................... 1-19
Bracket unit technical data ....................... 1-16
Break-in .................................................... 10-8
C.
Camshaft .................................................. 7-33
Canister .................................................... 6-17
Changing the engine oil............................ 10-9
Changing the gear oil ............................. 10-11
Charging unit and component .................. 5-19
Charging unit and starting unit (F150A, FL150A
[except for European and Oceanian markets]
and F150B, FL150B) ................................A-8
Charging unit and starting unit (F150A, FL150A
for European and Oceanian markets) ......A-6
Checking for fuel leakage/oil leakage..... 10-11
Checking the absorber valve .................... 9-44
Checking the air pressure sensor....5-24, 6-38
Checking the air temperature sensor ....... 5-23
Checking the anode.................................. 10-8
Checking the armature (PTT motor)......... 9-51
Checking the armature (starter motor) ..... 5-37
Checking the battery........................ 10-4, 10-8
Checking the big end oil clearance........... 7-67
Checking the brush................................... 9-51
Checking the brush holder........................ 5-37
Checking the button cell battery ............... 5-31
Checking the buzzer................................. 5-30
Checking the camshaft ............................. 7-35
Checking the canister ............................... 6-18
Checking the clamp bracket anode .......... 9-30
Checking the compression pressure .......... 7-1
Checking the connecting rod big end side
clearance ................................................ 7-66
Checking the connecting rod small end inside
diameter and big end inside diameter .... 7-66
Checking the cooling water inlet............... 10-8
Checking the cooling water pilot
hole................................................ 10-5, 10-9
Checking the cowling lock lever ............. 10-15
Checking the crankshaft ........................... 7-66
Checking the cylinder bore ....................... 7-64
Index i