i-5
Index
L.
Logging .....................................................2-12
Lower unit .................................................2-19
Lower unit
(counter rotation model)..........................1-19
Lower unit (counter rotation model, L-transom
model) .....................................................8-45
Lower unit (counter rotation model, X-transom
model) .....................................................8-48
Lower unit
(regular rotation model)...........................1-19
Lower unit (regular rotation model, L-transom
model) .......................................................8-1
Lower unit (regular rotation model, X-transom
model) .......................................................8-6
Lower unit technical data ..........................1-15
Lubricant, sealant, and thread locking
agent .........................................................0-6
Lubrication diagram ..................................2-16
Lubrication system ....................................2-16
M.
Maintenance interval chart 1.....................10-1
Maintenance interval chart 2.....................10-3
Manual format .............................................0-4
Measuring the forward and
reverse gear backlash
before disassembly .................................8-69
Measuring the forward gear backlash.......8-74
Measuring the forward gear
backlash..................................................8-41
Measuring the forward gear backlash and
reverse gear backlash before
disassembly ............................................8-35
Measuring the fuel pressure .......................6-5
Measuring the peak voltage......................5-12
Measuring the reverse gear backlash.......8-76
Measuring the reverse gear
backlash..................................................8-43
Model data ..................................................1-4
Model features ............................................1-1
Model name designation.............................1-2
N.
New functions ...........................................2-11
Non-reusable part .......................................0-3
O.
Oil pan and exhaust manifold ...................9-20
Optional equipment...................................3-14
Outboard motor mounting ...........................3-7
Outboard motor mounting instructions ....... 3-1
Outboard motor troubleshooting................. 4-6
Outline ...................................................... 10-1
Overview................................................... 2-10
P.
Part, lubricant, and sealant......................... 0-2
Pinion shim (T3) selection table ...............A-12
Port ............................................................. 5-1
Power unit................................................. 1-18
Power unit (check and adjustment) ............ 7-1
Power unit assembly .................................. 7-5
Power unit system .................................... 2-13
Power unit technical data ......................... 1-12
Predelivery check ..................................... 10-4
Propeller ..................................................... 0-1
Propeller (SDS) ........................................ 2-19
Propeller selection .................................... 3-38
Propeller shaft housing
(counter rotation model) ......................... 8-54
Propeller shaft housing
(regular rotation model) .......................... 8-13
Propeller shaft shim (T4) selection
table........................................................A-15
Propeller size............................................ 3-38
PTT cylinder ............................................. 9-41
PTT gear pump......................................... 9-54
PTT motor................................................. 9-48
PTT switch and cowling lock lever.............. 9-6
PTT system .............................................. 5-41
PTT unit ..................................1-20, 2-20, 9-33
R.
Rear............................................................ 5-5
Rectifier Regulator and ignition coil .......... 7-23
Reducing the fuel pressure......................... 6-5
Refacing the valve seat ............................ 7-43
Registering the receiver ID to the
ECM........................................................ 3-20
Removing the balancer assembly ............ 7-54
Removing the clamp bracket .................... 9-30
Removing the cowling lock lever ................ 9-8
Removing the crankcase cover ................ 7-60
Removing the cylinder head ..................... 7-40
Removing the drive shaft................. 8-21, 8-62
Removing the drive sprocket .................... 7-17
Removing the driven sprocket and
camshaft ................................................. 7-35
Removing the exhaust cover .................... 7-50
Removing the flushing hose ....................... 9-8
Removing the flywheel magnet ................ 7-13
Removing the fuel filter assembly............... 6-8
To Next Page
Loading...
