i-6
Index
0
1
2
3
5
6
7
8
9
10
10
A
Removing the fuel injector and vapor shut-off
valve........................................................6-18
Removing the fuel pump assembly...........6-13
Removing the gear pump assembly .........9-57
Removing the ignition coil .........................7-25
Removing the intake manifold...................6-37
Removing the lower unit ... 8-3, 8-8, 8-47, 8-50
Removing the oil filter bracket..........7-54, 7-60
Removing the oil pump assembly ....7-54, 7-60
Removing the power unit ............................7-7
Removing the propeller shaft housing
assembly........................................8-15, 8-56
Removing the PTT motor..........................9-50
Removing the PTT switch ...........................9-8
Removing the PTT unit .............................9-34
Removing the Rectifier Regulator .............7-25
Removing the reservoir.............................9-50
Removing the reverse gear.......................8-62
Removing the shift rod and shift bracket.....9-3
Removing the starter motor .............5-35, 7-21
Removing the stator assembly..................7-13
Removing the steering arm.......................9-25
Removing the throttle body assembly.......6-26
Removing the throttle link .........................6-23
Removing the tilt ram and trim ram...........9-43
Removing the timing belt ..........................7-17
Removing the upper case .........................9-15
Removing the vapor separator..................6-37
Removing the water pump and shift rod ...8-11
Removing the water pump and
shift rod ...................................................8-53
Removing the wiring harness....................7-30
Replacing the oil filter..............................10-10
Replacing the timing belt.........................10-15
Replacing the valve guide.........................7-42
Reverse gear shim (T1) selection chart
(FL150A) ................................................ A-16
Reverse gear shim (T1) selection chart
(FL150B) ................................................ A-17
Reverse gear shim (T2) selection chart
(F150A) .................................................. A-13
Reverse gear shim (T2) selection chart
(F150B) .................................................. A-14
Rigging grommet description ......................3-9
Rigging grommet mounting.........................3-9
Rigging information ...................................1-17
Rigging recommendation ..........................3-37
Rotating part ...............................................0-1
S.
Safety while working ...................................0-1
Selecting the crankpin bearing..................7-68
Selecting the crankshaft journal bearing...7-72
Selecting the pinion shim (T3) .........8-39, 8-73
Selecting the propeller shaft
shim (T4) ................................................ 8-73
Selection................................................... 3-38
Self-protection ............................................ 0-2
Serial number ............................................. 1-3
Setting the tilt limiter ................................. 3-18
Shift rod and shift bracket........................... 9-1
Shim location ................................... 8-38, 8-72
Shim selection table and chart (counter rotation
model).....................................................A-15
Shim selection table and chart (regular rotation
model).....................................................A-12
Shimless valve lifter.................................. 2-13
Shimming (counter rotation model) .......... 8-66
Shimming (regular rotation model) ........... 8-32
Shimming check sheet .................... 8-33, 8-67
Shimming procedure ....................... 8-38, 8-72
Shimming workflow.......................... 8-32, 8-66
Shock-absorbing function ......................... 2-23
Single outboard motor application
(conventional gauge) .............................. 3-31
Single outboard motor application (6Y8
Multifunction Meter) ................................ 3-29
Special service tool.............................. 0-3, 0-8
Specified tightening torque ....................... 1-17
Starter motor.................................... 5-33, 7-20
Starting unit and component..................... 5-27
Stationary condition .................................. 2-23
Steering arm ............................................. 9-24
Symbol........................................................ 0-6
Synchronizing the throttle valve................ 6-28
System diagram........................................ 3-29
T.
Test run .................................................... 10-7
Throttle body............................................. 6-25
Throttle body and throttle link adjustment. 6-27
Throttle link ............................................... 6-22
Tightening torque........................................ 0-3
Tilt limiter (F150A, FL150A [optional for
European and Oceanian markets])........... 2-9
Timing belt ................................................ 7-16
Top ............................................................. 5-6
Trim-down and tilt-down function.............. 2-21
Trim-up and tilt-up function....................... 2-20
Trouble code and checking step................. 4-8
Troubleshooting procedure......................... 4-6
Troubleshooting the power unit (trouble code
not detected)........................................... 4-11
Troubleshooting the power unit using the
diagnostic flash indicator ........................ 4-10
To Next Page
Loading...
