YASKAWA GA700 Series

Specifications
10
10.5 Drive Specifications
YASKAWA SIEPC71061705H GA700 Series Technical Manual 437
10.5 Drive Specifications
Note:
• To get the OLV, CLV, and AOLV specifications, do Rotational Auto-Tuning.
• To get the longest product life, install the drive in an environment that meets the necessary specifications.
Table 10.9 Control Characteristics
Item Specification
Control Methods
• V/f Control
• V/f Control with Encoder
• Open Loop Vector
• Closed Loop Vector
• Advanced Open Loop Vector
• PM Open Loop Vector
• PM Advanced Open Loop Vector
• PM Closed Loop Vector
• EZ Vector Control
Frequency Control
Range
• AOLVand EZOLV: 0.01 Hz to 120 Hz
• CL-V/f, CLV, AOLV/PM, and CLV/PM: 0.01 Hz to 400 Hz
• V/f, OLV, and OLV/PM: 0.01 Hz to 590 Hz
Frequency Accuracy
(Temperature
Fluctuation)
Digital inputs: ±0.01% of the maximum output frequency (-10 °C to +40 °C (14 °F to 104 °F))
Analog inputs: ±0.1% of the maximum output frequency (25 °C ±10 °C (77 °F ±18 °F))
Frequency Setting
Resolution
Digital inputs: 0.01 Hz
Analog inputs: 1/2048 of the maximum output frequency (11-bit signed)
Output Frequency
Resolution
0.001 Hz
Frequency Setting
Signal
Main speed frequency reference: -10 Vdc to +10 Vdc (20 kΩ), 0 Vdc to 10 Vdc (20 kΩ), 4 mA to 20 mA (250 Ω), 0 mA to 20 mA (250 Ω)
Main speed reference: Pulse train input (maximum 32 kHz)
Starting Torque
• V/f: 150%/3 Hz
• CL-V/f: 150%/3 Hz
• OLV: 200%/0.3 Hz
• CLV: 200%/0 min
-1
(r/min)
• AOLV: 200%/0.3 Hz
• OLV/PM: 100%/5% speed
• AOLV/PM: 200%/0 min
-1
(r/min)
• CLV/PM: 200%/0 min
-1
(r/min)
• EZOLV: 100%/1% speed
Note:
• Correctly select the drive and motor capacity for this starting torque in these control methods:
–OLV
–CLV
–AOLV
–AOLV/PM
–CLV/PM
• Set n8-57 = 1 [HFI Overlap Selection = Enabled] for this starting torque in AOLV/PM. When you use a non-Yaskawa PM motor, do Rotational
Auto-Tuning.
Speed Control Range
• V/f: 1:40
• CL-V/f: 1:40
• OLV: 1:200
• CLV: 1:1500
• AOLV: 1:200
• OLV/PM: 1:20
• AOLV/PM: 1:100
• CLV/PM: 1:1500
• EZOLV: 1:100
Note:
• Set n8-57 = 1 [HFI Overlap Selection = Enabled] for this Speed Control Range in AOLV/PM. When you use a non-Yaskawa PM motor, do
Rotational Auto-Tuning.
• Speed control range of 1:100 for AOLV/PM is Instantaneous operation range. Correctly select the drive and motor capacity for continuous operation.
Zero Speed Control
Possible in these control methods:
• CLV
• AOLV/PM
• CLV/PM