CS193/CS173/CS163 7-3
Copy paper/originals
7
7 Copy paper/originals
7.1 Copy paper
Use paper that meets the following specifications.
7.1.1 Possible paper sizes
Non-standard-sized paper:
* Banner paper
Paper width: 210 mm to 297 mm
Paper length: 457.3 mm to 1,200 mm
Standard-sized paper:
*1
There are five Foolscap sizes: 220 e 330 mm w, 8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w, and
8 e 13 w. Any one of these sizes can be selected. For details, contact your service representative.
*1
There are five Foolscap sizes: 220 e 330 mm w, 8-1/2 e 13 w, 8-1/4 e 13 w, 8-1/8 e 13-1/4 w and
8 e 13 w. Any one of these sizes can be selected. For details, contact your service representative.
*2
Can be used when the optional punch kit is installed on the finisher.
Paper source Paper width Paper length
Bypass tray* 90.0 mm to 311.1 mm 139.7 mm to 457.2 mm
Tray 1 – –
Tray 2
Single/Double paper feed cabi-
nets
LCT
Double-sided copies 139.7 mm to 311.1 mm 148 mm to 457.2 mm
Paper source Paper size
Bypass tray A3 w to B6 w, A6 w
12 e 18 w to 5-1/2 e 8-1/2 w/v, 8 e 13 w
*1
, 16K w/v, 8K w
Tray 1 A3 w to A5 w, 11 e 17 w to 8-1/2 e 11 w/v, 8 e 13 w
*1
, 16K v, 8K w
Tray 2 A3 w to A5 w, 12 e 18 w to 8-1/2 e 11 w/v, 8 e 13 w
*1
, 16K v, 8K w
Single/Double paper feed cabi-
nets
A3 w to A5 w, 11 e 17 w to 8-1/2 e 11 w/v, 8 e 13 w
*1
, 16K v, 8K w
LCT A4 v, 8-1/2 e 11 v
Double-sided copies A3 w to A5 w/v, 12-1/4 e 18 w, 12 e 18 w to 5-1/2 e 8-1/2, 8 e 13 w*1,
16K w/v, 8K w
Loaded equipment Paper sizes that can be loaded
Finisher (FS-519) Finishing tray 1, 2 and optional Output Tray
A3 w to B5 w, A6 w, 12- 1/4 e 18 w
"Group"/"Sort settings": A3 w to A5 v
Staple settings: A3 w to A5 v
Punch settings: A3 w, A4 v, B5 w
*2
Optional Output Tray
(OT-602)
Saddle Stitcher (SD-505) Fold & staple: A3 w, B4 w, A4 w, B5 w
Mailbin Kit (MT-502) A4 v, B5 v, A5 w
Job separator (JS-505) Finishing tray 1 and finishing tray 2
A3 w to B6 w, A6 w, 12- 1/4 e 18 w,
11 e 17 w to 5-1/2 e 8-1/2 w/v
To Next Page
Loading...
