Studer Vista - Page 34

Vista Digital Mixing System
1-20 Introduction SW V3.3 Date printed: 05.08.03
Control Room
Studio A
Talk to
CR
Ret 1
Ext 1
Studio Monitor A
Red
Light
SIG1
SIG2
TB only
PFL/TB Out
CR Monitor
Signaling Keys
Talk to
Aux 1
Talk to
Aux 2
Talk to
Aux 3
Talk to
Aux 4
Talk to
Aux 1
Talk to
Aux 2
Talk to
Ext 1
Talk to
Ext 2
Talk to
Aux 3
Talk to
Aux 4
Talk to
preselected
Talk to
preselected
Talk to
Studio B
e. g. Speaker
GPI 1
GPI 3
GPI 4
GPO 2
GPO 1
GPI 0
Foot Switch
GPI 6 GPI 7 GPI 8 GPI 9 GPI 10
e. g. Intercom
Ext 3
(Line level)
(always on)
Vista6 Desk
Mic "TB2"
TB Mic
GPO 0
Ext Location 1
Producer
(-> to PFL Speaker)
Talkback and Signaling Block Diagram
Studio B
Talk to
CR
Ret 2
Ext 2
Studio Monitor B
GPI 2
Ext Location 2
(-> to PFL Speaker)
Talk to
Studio A
GPI 5
GPI X
Talk to
ChanOut
Grp 01
Talk to
ChanOut
Grp n
Channel
Mute
Grp 01
Channel
Mute
Grp n
Talk to
EXT1
Talk to
EXT2
GPI12
GPI11
GPI X GPI X GPI X GPI XGPI XGPI X
Selector
Studio A
Selector
Studio B
On Air
Talk to
Studio
GPI X
GPO 3
GPO X
GPO X
GPI X
GPI X
GPO X
GPO X
e. g. Speaker
GPO 5
GPO X
TB Keys
GPO 4
Legend :
GPI 1
GPO 2
GPI X
= GPI already configured in *.ini files
= GPO already configured in *.ini files
= GPI prepared to use, but not assigned to signaling card.
This can be configured in *.ini files
GPO X
= GPO prepared to use, but not assigned to signaling card.
This can be configured in *.ini files
Desk Operator
GPO X
Producer area (either in control room or in another room)
Relations :
Dim CR and PFL if : Anytalk in Desk OR (Anytalk Producer AND Producer located in CR) [DimLock is activated]
Dim StudioA if : Ret1 Talk to CR AND Ret1 located in Studio [DimLock is activated]
Dim StudioB if : Ret2 Talk to CR AND Ret2 located in Studio [DimLock is activated]
Cut StudioA if : (Faderstart of source which is assigned to StudioA) OR (StudioA is OnAir)
Cut StudioB if : (Faderstart of source which is assigned to StudioB) OR (StudioB is OnAir)
Cut Ext1 if : StudioA Cut AND Ret1 located in Studio
Cut Ext2 if : StudioB Cut AND Ret2 located in Studio
Sig1 LED StudioA = Sig1OutStudioA OR Sig1InStudioA
Sig2 LED StudioA = Sig2OutStudioA OR Sig2InStudioA
RedLight StudioA = StudioA Cut OR RedlightStudioA manual
TalkLED StudioA = DeskTalktoStudioA OR Ret1TalktoCR
Sig1 LED StudioB = Sig1OutStudioB OR Sig1InStudioB
Sig2 LED StudioB = Sig2OutStudioB OR Sig2InStudioB
RedLight StudioB = StudioB Cut OR RedlightStudioB manual
TalkLED StudioB = DeskTalktoStudioB OR Ret2TalktoCR
OnAirMode = OnAirKey OR GPI