YASKAWA GA700 Series

5.2 European Standards
222 YASKAWA SIEPC71061705H GA700 Series Technical Manual
Model Terminal
Recomm. Gauge
mm
2
Applicable Gauge
(IP20 Applicable Gauge
*1
)
mm
2
Wire Stripping
Length
*2
mm
Terminal Screw
Size and Shape
Tightening Torque
N∙m (lbf∙in)
2211
R/L1, S/L2, T/L3 95
50 - 95
(95)
37
M10
12 - 14
(107 - 124)
U/T1, V/T2, W/T3 95
50 - 95
(95)
37
M10
12 - 14
(107 - 124)
-, -, +1, +1
*5 *6
50
16 - 50
(50)
28
M6
8 - 9
(71 - 80)
+3
*6
70
25 - 70
(50 - 70)
28
M8
8 - 9
(71 - 80)
50
25 - 50
(-)
-
M8
9.0 - 11
(79.7 - 97.4)
2257
R/L1, S/L2, T/L3 50 × 2P
25 - 95 × 2P
(70 - 95 × 2P)
-
M10
20
(177)
U/T1, V/T2, W/T3 50 × 2P
25 - 95 × 2P
(70 - 95 × 2P)
-
M10
20
(177)
-, +1 70 × 2P
35 - 120 × 2P
(120 × 2P)
-
M10
20
(177)
+3 35 × 2P
25 - 70 × 2P
(70 × 2P)
-
M10
20
(177)
95
95 - 240
(-)
-
M10
18 - 23
(159 - 204)
2313
R/L1, S/L2, T/L3 70 × 2P
25 - 95 × 2P
(70 - 95 × 2P)
-
M10
20
(177)
U/T1, V/T2, W/T3 70 × 2P
25 - 95 × 2P
(70 - 95 × 2P)
-
M10
20
(177)
-, +1 95 × 2P
35 - 120 × 2P
(120 × 2P)
-
M10
20
(177)
+3 50 × 2P
25 - 70 × 2P
(70 × 2P)
-
M10
20
(177)
95
95 - 240
(-)
-
M10
18 - 23
(159 - 204)
2360
R/L1, S/L2, T/L3 120 × 2P
70 - 150 × 2P
(150 × 2P)
-
M12
35
(310)
U/T1, V/T2, W/T3 120 × 2P
70 - 150 × 2P
(150 × 2P)
-
M12
35
(310)
-, +1 120 × 2P
95 - 185 × 2P
(185 × 2P)
-
M12
35
(310)
+3 70 × 2P
50 - 95 × 2P
(-)
-
M12
35
(310)
120
120 - 240
(-)
-
M12
32 - 40
(283 - 354)
2415
R/L1, S/L2, T/L3 120 × 2P
70 - 150 × 2P
(150 × 2P)
-
M12
35
(310)
U/T1, V/T2, W/T3 120 × 2P
70 - 150 × 2P
(150 × 2P)
-
M12
35
(310)
-, +1 120 × 2P
95 - 185 × 2P
(185 × 2P)
-
M12
35
(310)
+3 70 × 2P
50 - 95 × 2P
(-)
-
M12
35
(310)
120
120 - 240
(-)
-
M12
32 - 40
(283 - 354)
*1 For IP20 protection, use wires that are in the range of applicable gauges.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than 30 mm
2
, tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lbf∙in to 40 lbf∙in).
*4 Install an RCM/RCD with this wire gauge to maintain compliance with IEC/EN 61800-5-1:2007.
*5 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*6 A junction terminal is necessary to connect a braking unit (CDBR-series) to terminals - and +3.