Zebra ZM400 Series User Manual

17
List of Figures
8/9/07 ZM400/ZM600 Maintenance Manual 14207L-001 A
Figure 73 • Remove the Pressure Bracket and Roller .....................................................................202
Figure 74 • Remove the Pressure Dials ...........................................................................................203
Figure 75 • Install the Springs ..........................................................................................................203
Figure 76 • Align the Forks and Bearings ........................................................................................204
Figure 77 • Locate the Electronics Cover Mounting Screw ..............................................................207
Figure 78 • Remove the Electronics Cover Mounting Screws .........................................................208
Figure 79 • Remove the Electronics Cover ......................................................................................208
Figure 80 • Locate the Magnetic Latch ............................................................................................209
Figure 81 • Remove the Old Magnetic Latch ...................................................................................210
Figure 82 • Install the New Magnetic Latch .....................................................................................211
Figure 83 • Locate the Upper and Lower Flanges ...........................................................................212
Figure 84 • Locate the Electronics Cover Mounting Screw ..............................................................215
Figure 85 • Remove the Electronics Cover Mounting Screws .........................................................216
Figure 86 • Remove the Electronics Cover ......................................................................................216
Figure 87 • Remove the Radio Card ................................................................................................217
Figure 88 • Remove the Wireless Board ..........................................................................................218
Figure 89 • Remove the Standoff and Screw ...................................................................................219
Figure 90 • Gain Access the Power Supply .....................................................................................220
Figure 91 • Locate Drive System Components ................................................................................221
Figure 92 • Disconnect the Media Sensor Cables ...........................................................................222
Figure 93 • Remove the Upper Media Sensor Mounting Screw ......................................................223
Figure 94 • Release the Dancer Spring ...........................................................................................224
Figure 95 • Remove the Media Sensor Assemblies ........................................................................225
Figure 96 • Remove the Protective Cap ..........................................................................................226
Figure 97 • Locate the Access Hole .................................................................................................227
Figure 98 • Remove the Protective Cap ..........................................................................................228
Figure 99 • Install the Upper Media Sensor Assembly ....................................................................229
Figure 100 • Adjust the ZM400 Upper Media Sensor ......................................................................233
Figure 101 • Adjust the ZM600 Upper Media Sensor ......................................................................234
Figure 102 • Locate the Electronics Cover Mounting Screw ............................................................236
Figure 103 • Remove the Electronics Cover Mounting Screws .......................................................237
Figure 104 • Remove the Electronics Cover ....................................................................................237
Figure 105 • Disconnect the Ribbon/Head Open Sensor ................................................................238
Figure 106 • Ribbon Sensor Removal and Installation ....................................................................239
Figure 107 • Locate the Access Hole ...............................................................................................240
Figure 108 • Gap Measurement Between Print Mechanism and Sensor ........................................241
Figure 109 • Locate the Upper and Lower Flanges .........................................................................242
Figure 110 • Locate the Electronics Cover Mounting Screw ............................................................245
Figure 111 • Remove the Electronics Cover Mounting Screws .......................................................246
Figure 112 • Remove the Electronics Cover ....................................................................................246
Figure 113 • Lay the Printer on its Side ...........................................................................................247
Figure 114 • Remove the Gear Cover .............................................................................................248
Figure 115 • Remove and Install Gears, Pulley, and Belt ................................................................249
Figure 116 • Locate the Upper and Lower Flanges .........................................................................251
Figure 117 • Locate the Electronics Cover Mounting Screw ............................................................252
Figure 118 • Remove the Electronics Cover Mounting Screws .......................................................253
Figure 119 • Remove the Electronics Cover ....................................................................................253
Figure 120 • Remove the Old Belt ...................................................................................................254
Figure 121 • Locate the Upper and Lower Flanges .........................................................................255
Figure 122 • Locate the Electronics Cover Mounting Screw ............................................................257
Figure 123 • Remove the Electronics Cover Mounting Screws .......................................................258
Figure 124 • Remove the Electronics Cover ....................................................................................258

Zebra ZM400 Series Specifications

General

Brand	Zebra
Model	ZM400 Series
Category	Label Maker
Language	English