YASKAWA GA700 Series

3.9 Braking Resistor Installation
112 YASKAWA SIEPC71061705H GA700 Series Technical Manual
Table 3.17 200 V Class
Drive Model
Braking Unit
(Qty)
Drive Terminals
Recomm. Gauge
(mm
2
)
Applicable Gauge
(mm
2
)
Ref.
2257
CDBR-2022D
(× 2)
Specified Wire Gauge
+3 6 × 2P 6 - 10 × 2P Figure 3.59
- 6 × 2P 6 - 10 × 2P Figure 3.59
Applicable Gauge
*1
+3 35 × 2P 25 - 70 × 2P Figure 3.60
- 35 × 2P
*2
25 - 70 × 2P
*2
Figure 3.60
2313
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.59
- 35 35 Figure 3.59
Applicable Gauge
*1
+3 50 × 2P 25 - 70 × 2P Figure 3.60
- 50 × 2P
*2
25 - 70 × 2P
*2
Figure 3.60
2360
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.61
- 35 35 Figure 3.61
2415
CDBR-2110D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.61
- 35 35 Figure 3.61
*1 This is the applicable wire gauge when you use a braking unit other than Yaskawa braking unit (CDBR-type).
*2 This is the applicable wire gauge when you use the same wires for terminals - and +3.
Table 3.18 400 V Class
Drive Model
Braking Unit
(Qty)
Drive Terminals
Recomm. Gauge
(mm
2
)
Applicable Gauge
(mm
2
)
Ref.
4208
CDBR-4045D
(× 2)
Specified Wire Gauge
+3 6 × 2P 6 - 10 × 2P Figure 3.59
- 6 × 2P 6 - 10 × 2P Figure 3.59
Applicable Gauge
*1
+3 35 × 2P 25 - 70 × 2P Figure 3.60
- 35 × 2P
*2
25 - 70 × 2P
*2
Figure 3.60
4250
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.59
- 35 35 Figure 3.59
Applicable Gauge
*1
+3 50 × 2P 25 - 70 × 2P Figure 3.60
- 50 × 2P
*2
25 - 70 × 2P
*2
Figure 3.60
4296
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.59
- 35 35 Figure 3.59
Applicable Gauge
*1
+3 70 × 2P 25 - 70 × 2P Figure 3.60
- 70 × 2P
*2
25 - 70 × 2P
*2
Figure 3.60
4371
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.61
- 35 35 Figure 3.61
4389
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.61
- 35 35 Figure 3.61
4453
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.62
- 35 35 Figure 3.62
Applicable Gauge
*1
+3 70 × 4P 35 - 95 × 4P Figure 3.64
- 70 × 4P
*2
35 - 95 × 4P
*2
Figure 3.64
4568
CDBR-4220D
(× 1)
Specified Wire Gauge
+3 35 35 Figure 3.62
- 35 35 Figure 3.62
Applicable Gauge
*1
+3 70 × 4P 35 - 95 × 4P Figure 3.64
- 70 × 4P
*2
35 - 95 × 4P
*2
Figure 3.64