EasyManuals Logo

Fujitsu PRIMERGY TX300 S8 User Manual

Fujitsu PRIMERGY TX300 S8
792 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
10 Upgrade and Maintenance Manual TX300 S8 / RX350 S8
Inhalt
5.2 Completing the maintenance task . . . . . . . . . . . . . . 134
5.2.1 Updating or recovering the system board BIOS and iRMC . . . 134
5.2.1.1 Updating or recovering the system board BIOS . . . . . . . 134
5.2.1.2 Updating or recovering the iRMC . . . . . . . . . . . . . . 134
5.2.2 Verifying system information backup / restore . . . . . . . . . 136
5.2.3 Updating RAID controller firmware . . . . . . . . . . . . . . . 137
5.2.4 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . 138
5.2.5 Verifying and configuring the backup software solution . . . . . 139
5.2.6 Resetting the boot retry counter . . . . . . . . . . . . . . . . 140
5.2.6.1 Viewing the boot retry counter . . . . . . . . . . . . . . . 140
5.2.6.2 Resetting the boot retry counter . . . . . . . . . . . . . . . 140
5.2.7 Resetting the error status after replacing memory modules
or processors . . . . . . . . . . . . . . . . . . . . . . . . . . 142
5.2.7.1 Memory modules . . . . . . . . . . . . . . . . . . . . . . 142
5.2.7.2 Processors . . . . . . . . . . . . . . . . . . . . . . . . . 143
5.2.8 Performing a fan test after replacing a defective fan . . . . . . 145
5.2.9 Enabling SVOM boot watchdog functionality . . . . . . . . . . 146
5.2.10 Enabling replaced components in the system BIOS . . . . . . 147
5.2.11 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 147
5.2.12 Verifying the system time settings . . . . . . . . . . . . . . . 148
5.2.13 Viewing and clearing the System Event Log (SEL) . . . . . . . 149
5.2.13.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 149
5.2.13.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . 150
5.2.14 Updating the NIC configuration file in a Linux environment . . . 150
5.2.15 Resuming BitLocker functionality . . . . . . . . . . . . . . . . 152
5.2.16 Performing a RAID array rebuild . . . . . . . . . . . . . . . . 153
5.2.17 Looking up changed MAC / WWN addresses . . . . . . . . . 153
5.2.17.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 154
5.2.17.2 Looking up WWN addresses . . . . . . . . . . . . . . . . 154
5.2.18 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . 155
5.2.19 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 156
5.2.19.1 After replacing / upgrading LAN controllers . . . . . . . . . 157
5.2.19.2 After replacing the system board . . . . . . . . . . . . . . 157
5.2.20 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 158
5.2.21 Specifying the chassis model . . . . . . . . . . . . . . . . . . 158

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fujitsu PRIMERGY TX300 S8 and is the answer not in the manual?

Fujitsu PRIMERGY TX300 S8 Specifications

General IconGeneral
BrandFujitsu
ModelPRIMERGY TX300 S8
CategoryServer
LanguageEnglish

Related product manuals