Gemalto Cinterion EHS6 User Manual

Cinterion
®
EHS6 AT Command Set 
10.6 AT^SISO
 EHS6_ATC_V03.001 15/12/3
Confidential / Released
Page 245 of 513
10.6 AT^SISO Internet Service Open
The AT^SISO write command starts the Internet session configured by the service profile. All further steps
needed to control the session depend on whether you are using URC mode or polling mode. The AT^SISO read
command returns the current status of all Internet services. 

URC mode (not for the Transparent TCP Listener service):
If the service opens successfully, the URCs "^SISW" and "^SISR" will trigger the action to follow, either writing
data with AT^SISW or reading data with AT^SISR. To terminate an upload data stream set the <eodFlag>
within the last AT^SISW command. If the URCs notify that a data transfer has been successful ("^SISR: x, 2" or
"^SISW: x, 2"), the service can be closed with AT^SISC. If a special event occurs, e.g. an error or a warning,
after opening or while using a service then the URC type "^SIS" will be delivered. 

Polling mode:
After opening the service, all progress information needed to control the session shall be explicitly requested by
the host application. The particular sequence of AT commands varies depending on the service used. The fol-
lowing list summarizes, by way of an example, the steps normally involved in managing an upload or download
job.
• Upload (Socket, FTP, HTTP,SMTP):
- Enter the AT^SISO command, e.g. AT^SISO=9.
-Enter AT^SISW, specify <reqWriteLength>, e.g. AT^SISW=9,20. Check resulting response for
<cnfWriteLength>. Optionally, check error with AT^SISE, e.g. AT^SISE=9. If necessary, repeat the
sequence several times.
- Enter last AT^SISW command and enable <eodFlag>, e.g. AT^SISW=9,0,1. 
If Socket service: Query available data with AT^SISR, e.g. AT^SISR=9,1430.
- Check service state with AT^SISI, e.g. AT^SISI=9, if necessary several times until <srvState>=6
("Down").
- Check error with AT^SISE, e.g. AT^SISE=9.
- Close service with AT^SISC, e.g. AT^SISC=9.
• Download (Socket, FTP, HTTP):
- Enter the AT^SISO command, e.g. AT^SISO=9.
-Enter AT^SISR, specify <reqReadLength>, e.g. AT^SISR=9,1000. Check resulting response for
<cnfReadLength>
. If necessary, repeat the sequence several times until <cnfReadLength>= -2 (end
of data) or ERROR.
- Check error with AT^SISE, e.g. AT^SISE=9.
- Close service with AT^SISC, e.g. AT^SISC=9.
• Socket service (upload and download possible in one session):
- Recommended: Set AT+CMEE=2 to enable extended error text.
- Enter the AT^SISO command, e.g. AT^SISO=9.
-Enter AT^SISR or AT^SISW, specifying <reqReadLength> or <reqWriteLength>, e.g.
AT^SISR=9,20 or AT^SISW=9,20. Check resulting response for <cnfReadLength> or <cnfWrite-
Length>. If necessary, repeat the sequence several times.
- Check error with AT^SISE, e.g. AT^SISE=9.
- If write action: Enter last AT^SISW command and enable <eodFlag>, e.g. AT^SISW=9,0,1.
1)

If Socket service: Query available data with AT^SISR, e.g. AT^SISR=9,1430.
- Close service with AT^SISC, e.g. AT^SISC=9.
• Transparent TCP client or Transparent UDP client:
- Enter the AT^SISO command, e.g. AT^SISO=9.
-Enter AT^SIST to enter transparent data mode. After communication has finished return to AT command
mode via +++ escape sequence.
- Check error with AT^SISE, e.g. AT^SISE=9.
- Close service with AT^SISC, e.g. AT^SISC=9.

Gemalto Cinterion EHS6 Specifications

General

Brand	Gemalto
Model	Cinterion EHS6
Category	Control Unit
Language	English