Lenze 9300 - Page 463

Configuration
7-332
L
EDSVS9332P-D22 EN 3.0
Code ImportantPossible settings
No. SelectionLenzeLCD
C0200 S/W ID 0 Software identification
Software identification
C0201 S/W DATE 0 Date of software release
Creation da te
C0202 I NTERNAL IO 0 0.000 {0.001} 100.000 Internal identification
C0203 COMM. NO. 0 x / xxxx / xxxxx Commission number
C0204 SERIAL-NO. 0 0 {1} 65535 Serial number
C0206 PRODUCT DATE 0 Date of production
C0207 DL INFO 1 0 Download info 1
C0208 DL INFO 2 0 Download info 2
C0209 DL INFO 3 0 Download info 3
C0220 NSET TIR ADD 0.000 0.000 {0.001 s} 999.900 NSET
Additional setpoint Tir
Acceleration time T
ir
of the additional setpoint
for NSET
(referring to speed variation of 0 ... n
max.
)
C0221 NSET TIF ADD 0.000 0.000 {0.001 s} 999.900 NSET
Additional setpoint Tif
Deceleration time T
if
of the additional setpoint
for NSET
(referring to speed variation of 0 ... n
max.
)
C0222 PCTRL VP 1.0 0.1 {0.1} 500.0 PCTRL
Vp gain
C0223 PCTRL TN 400 20 {1 ms} 99998 PCTRL
Tn integral component
99999 ms: Switched off
C0224 PCTRL KD 0.0 0.0 {0.1} 5.0 PCTRL
Kd differential component
C0241 NSET RFG-I = O 1.00 0.00 {0.01 %} 100.00 NSET
Threshold ramp function generator for main
setpoint
Input = output , (100 % = n
max
)
C0244 BRK M SET 0.00 -100.00 {0.01 %} 100.00 BRK1
Holding torque of the DC injection brake
100 % = value of C0057
C0250 FCODE 1BIT 0 0
1
lower limit
upper limit
FCODE 1bit digital
C0252 ANGLE OFFSET 0 -245760000 {1 inc} 245760000 DFSET
Phase offset
Fixed phase offset for digital frequency
configuration
1 rev. = 65536 inc
C0253 ANGLE N-TRIM → -32767 {1 inc} 32767 DFSET
Speed-dependent phase trimming
Æ depending on C0005, C0025, C0490
Change of C0005, C0025, or C0490 resets
C0253 to the default setting
1 rev. = 65536 inc
C0253 is reached at 15000 rpm
C0254 VP ANGLE CTRL 0.4000 0.0000 {0.0001} 3.9999 MCTRL
Vp phase controller
C0255 THRESHOLD P03 327680 10 {1 inc} 1800000000 Following error limit P03
1 rev. = 65536 inc
Following error > C0255 releases fault ”P03”
C0260 MPOT1 HIGH 100.00 -199.99 {0.01 %} 199.99 MPOT1
Upper limit (condition: C0260 > C0261)
C0261 MPOT1 LOW -100.00 -199.99 {0.01 %} 199.99 MPOT1
Lower limit (condition: C0261 < C0260)
Show/Hide Bookmarks