EasyManua.ls Logo

Mitsubishi FX3U-232-BD - 1.4.2 Programming software for remote maintenance

Mitsubishi FX3U-232-BD
668 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
I-9
FX Series PLC User's Manual - Data Communication Edition
Remote Maintenance
1 Outline
1.4 Programming Tool Applicability
A
Common Items
B
N:N Network
C
Parallel Link
D
Computer Link
E
Inverter
Communication
F
Non-Protocol
Communication
(RS/RS2 Instruction)
G
Non-Protocol
Communication
(FX
2N
-232IF)
H
Programming
Communication
I
Remote
Maintenance
Apx.
Discontinued
models
1.4.2 Programming software for remote maintenance
The table below shows programming software for the personal computer which uses remote access.
For the applicability of programming tools for setting the modem, refer to Subsection 1.4.1.
In the case of applicable versions
The programming software is applicable from the following versions:
1. Japanese versions
: Applicable (If applicable versions are limited, they are described inside ( ).)
—: Not applicable
2. English versions
: Applicable (If applicable versions are limited, they are described inside ( ).)
—: Not applicable
3. In the case of non-applicable versions
A non-applicable programming software version cannot offer remote maintenance.
If your programming software is a non-applicable version, upgrade versions.
To upgrade versions, contact your dealer.
Model name
(Software name)
Applicability
(applicable version)
Remarks
FX3U and FX3UC PLCs
GX Developer
SWD5C(F)-GPPW-J
(Ver. SW8 P or later)
Ver. 8.13P
Select the model "FX3U/FX3UC"
When connecting the programming software to a PLC in
which the PP modem mode (ch1) or PP modem mode (ch2)
is set, use Ver. 8.18U or later.
FX2N and FX2NC PLCs
GX Developer
SWD5C(F)-GPPW-J
(Ver. SW2 A or later)
Select the model "FX2N/FX2NC"
FX-PCS/WIN
SW0PC-FXGP/WIN
(Ver. 2.10 or later)
FX1S, FX1N and FX1NC PLCs
GX Developer
SWD5C(F)-GPPW-J
(Ver. SW5 A or later)
Select the model "FX1S/FX1N/FX1NC"
FX-PCS/WIN
SW0PC-FXGP/WIN
(Ver. 4.00 or later)
Model name
(Software name)
Applicability
(applicable version)
Remarks
FX3U and FX3UC PLCs
GX Developer
SWD5C(F)-GPPW-E
(Ver. SW8 P or later)
Ver. 8.13P
Select the model "FX3U/FX3UC"
When connecting the programming software to a PLC in
which the PP modem mode (ch1) or PP modem mode (ch2)
is set, use Ver. 8.18U or later.
FX2N and FX2NC PLCs
GX Developer
SWD5C(F)-GPPW-E
(Ver. SW2 A or later)
Select the model "FX2N/FX2NC"
FX-PCS/WIN-E
SW0PC-FXGP/WIN-E
(Ver. 1.00 or later)
FX1S, FX1N and FX1NC PLCs
GX Developer
SWD5C(F)-GPPW-E
(Ver. SW5 A or later)
Select the model "FX1S/FX1N/FX1NC"
FX-PCS/WIN-E
SW0PC-FXGP/WIN-E
(Ver. 3.00 or later)

Table of Contents

Related product manuals