YASKAWA GA700 Series

978 YASKAWA SIEPC71061705H GA700 Series Technical Manual
oL2................................................................. 912
Overcurrent....................................................... 913
Overload .......................................................... 912
PF .................................................................. 910
rr ................................................................... 916
Uv1 ................................................................ 883
Protective function
Desynchronization............................................... 917
Drive Overheating ............................................... 909
HCA ............................................................... 915
LF.................................................................. 911
Low Speed Desynchronization ................................ 917
LSo ................................................................ 917
oH.................................................................. 909
Output Current Overload ....................................... 915
Output Phase Loss Detection .................................. 911
Software Current Limit Selection ............................. 912
Pulse Train Input
Terminal RP Function Selection............................... 864
Pulse Train Input/Output
Parameter ......................................................... 864
Pulse train output
Terminal MP function selection ............................... 866
Wiring specifications............................................ 104
PWEr................................................................... 371
R
Rating (200 V)
Drive............................................................... 428
Rating (400 V)
Drive............................................................... 431
rdEr..................................................................... 371
Ready
LED status ........................................................ 141
Remove
Front cover ........................................................ 49
Keypad ............................................................. 43
Terminal cover .................................................... 49
RESET key............................................................ 135
Residual Current Monitor/Residual Current Device
RCM/RCD........................................................ 118
Wiring ............................................................. 118
Restore
Parameters (Auto Backup) ..................................... 183
Parameters (keypad to drive)................................... 164
Reverse Operation Selection........................................ 647
rF ....................................................................... 345
rH ....................................................................... 345
RJ-45 connector ...................................................... 135
Rotational Auto-Tuning
Induction Motor.................................................. 186
PM Motors........................................................ 187
Precautions ....................................................... 192
rr ........................................................................ 346
Protection Functions ............................................ 916
rUn ..................................................................... 357
RUN
LED status ........................................................ 141
Run command
LOCAL/REMOTE Run selection ............................. 643
Switching between LOCAL/REMOTE....................... 643
Run Command at Power Up ........................................ 653
Run Command Selection 2
Switching between LOCAL/REMOTE....................... 652
RUN indicator .................................................. 135, 137
RUN key............................................................... 135
S
S-curve characteristics
Parameter ......................................................... 697
Sampling time setting
Data log ........................................................... 179
SC ...................................................................... 346
SCF..................................................................... 346
SE....................................................................... 357
SEr...................................................................... 346
Serial communication terminals
MEMOBUS/Modbus Communications ....................... 99
Set date and time
Operation ......................................................... 173
Set time
Operation ......................................................... 173
Setup Wizard
Operation ......................................................... 175
Short Circuit Braking
Parameter ......................................................... 654
Side-by-side
Derating..................................................... 444, 914
Simple Positioning Stop ............................................. 729
Slip compensation
Parameter ......................................................... 698
Softcharge Relay Maintenance Set................................. 954
Software Current Limit Selection
Protective function .............................................. 912
Software version
Display procedure ............................................... 182
Speed Agreement
Parameter ......................................................... 896
Speed Detection
Parameter ......................................................... 896
Speed Estimation Speed Search .................................... 659
Speed limit
Parameter ......................................................... 732
Speed Search function
Operation during momentary power loss..................... 881
Parameter ......................................................... 657
Stall Prevention function
Parameter ......................................................... 886
Stationary Auto-Tuning
Induction Motor.................................................. 186
PM Motors........................................................ 187
Precautions ....................................................... 193
Stationary Auto-Tuning for Line-to-Line Resistance............ 186
Precautions ....................................................... 193
Stator resistance Auto-Tuning ...................................... 187
Precautions ....................................................... 193
STo ..................................................................... 357
SToF.................................................................... 358
Stop command
LOCAL/REMOTE Run selection ............................. 643
STOP key.............................................................. 135
STOP Key Function Selection...................................... 948
Stop Position Gain ................................................... 731
Stopping Method Selection ......................................... 643
STPo ................................................................... 346
Surge protective device
Connection........................................................ 122
SvE ..................................................................... 346
T
Temperature
Environment....................................................... 34
Terminal block ........................................................ 100
Configuration of main circuit terminal block ................. 68
Control circuit terminal block functions....................... 95