B. Braun Dialog+ - Page 349

5. Technical Safety Inspection and Preventive Maintenance 1/2010 5 - 4
BA-TE-DE08C M.KAY Dialog+ SW9xx_SM_Chapter 5-1_1-2010.doc/pdf <110301> yymmdd B. Braun Avitum AG
Dialog
+
SW 9.xx
S M
Check List (S = Technical Safety Inspection Points; M = Preventive Maintenance Points)
Note: Text in { } brackets is information for the execution of the check list!
NO YES OK
M
2.22 Conductivity Sensors
2.22.1 ENDLF sensor: Visual inspection
  
2.22.2 BICLF sensor: Visual inspection
  
M
2.23 Piston Pumps
2.23.1 BIC piston pump: Visual inspection
  
2.23.2 KP piston pump: Visual inspection
  
M
2.23.3 UF piston pump: Visual inspection
  
M
2.24 Blood leak detector (BLD) test passed
  
2.24.1
Check blood leak detector and calibrate if necessary
n
  
M
2.25
Degassing Pressure Sensor PE (permissible tolerance ±13 [mbar])
- Comparison measurement (at approx. -530): Measurement instrument: ......................... Display on machine: ......................... [mbar]

- Comparison measurement (at approx. -130): Measurement instrument: ......................... Display on machine: ......................... [mbar]

M
2.26
Dialysate Outlet Pressure Sensor PDA (permissible tolerance ±13 [mbar])
- Comparison measurement (at approx. -530): Measurement instrument: ......................... Display on machine: ......................... [mbar]

- Comparison measurement (at approx. 0): Measurement instrument: ......................... Display on machine: ......................... [mbar]

- Comparison measurement (at approx. +530): Measurement instrument: ......................... Display on machine: ......................... [mbar]

M
2.27
Heparin Pump
2.27.1
Position (80 mm ± 15 mm) {Drive fast forward to end position with 30 ml syringe. Check display position in mm.} ......................... [mm]

M
2.28 Set summer/winter time {TSM, Treatment Support, System Configuration, if applicable in this country}
  
3. Function Inspection (Document Measurement Values)
S
3.1
Blood Pump: - Check function, moveability, noise rating

3.1.1 - Check roller/one-way bearing; clean and lubricate shaft slightly if necessary

3.1.2 - Alarm cover switch

S
3.2
Single-Needle Pump:
Option present
  
3.2.1 - Check function, moveability, noise rating

3.2.2 - Check roller/one-way bearing; clean and lubricate shaft slightly if necessary

3.2.3 - Alarm cover switch

S
3.3
Venous Tubing Clamp SAKV: - Function/gap checked, set gap 1.4 (+0.1 mm) if necessary

S
3.4
Arterial Tubing Clamp SAKA:
Option present
  
3.4.1 - Function/gap checked, set gap 1.4 (+0.1 mm) if necessary

S
3.5
Arterial Pressure PA: (permissible. tolerance ±10 [mmHg])
Comparison measurement (at approx. -400): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

Comparison measurement (at approx. 0): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

S
3.6
Inlet Pressure PBE: (permissible. tolerance ±10 [mmHg])
Comparison measurement (at approx. 0): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

Comparison measurement (at approx. +400): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

S
3.7
Venous Pressure PV: (permissible. tolerance ±10 [mmHg])
- Comparison measurement (at approx. 0): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

Comparison measurement (at approx. +400): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

S
3.8
Single-Needle Pressure PBS: (permissible. tolerance ±10 [mmHg])
Option present
  
- Comparison measurement (at approx. 0): Measurement instrument: ......................... Display on machine: ...................... [mmHg]

- Comparison measurement (at approx. +400): Measurement instrument: ......................... Display on machine: ...................... [mmHg]
