TECO A510s - Page 53

3-38
A510S Model wire diameter (mm
2
)
NFB
*4
MC
*4
Power
horse
power
(HP)
*1
Rated
KVA
HD/ND
Rated
current
(A)
HD/ND
Main
circuit
*2
Groundin
g
line
E(G)
Control
line
*3
175HP 198/226 260/296 200 30
0.5～2
TO-400S(400A) CN-300
215HP 225/250 295/328 250 30
0.5～2
TO-400S(400A) CN-300
270HP 290/332 380/435 300 38
0.5～2
TO-400S(400A) SK-400
300HP 343/393 450/515 250*2P 50
0.5～2
TO-800S(800A)
SK-600
(800A)
375HP 400/446 523/585 250*2P 50
0.5～2
TE-1000(1000A)
SK-600
(800A)
425HP 446/446 585/585 250*2P 50
0.5～2
TE-1000(1000A)
SK-600
(800A)
575V
3 Ø
1HP 1.7/3.0 1.7/3.0 2～5.5 2～5.5 0.5～2 TO-50EC(15A) CU-11
2HP 3/4.2 3/4.2 2～5.5 2～5.5 0.5～2 TO-50EC(15A) CU-11
3HP 4.2/5.8 4.2/5.8 2～5.5 3.5～5.5 0.5～2 TO-50EC(15A) CU-11
5HP 6.6/8.8 6.6/8.8 2～5.5 3.5～5.5 0.5～2 TO-50EC(15A) CU-11
7.5HP 9.9/12.1 9.9/12.2
3.5～5.5
3.5～5.5 0.5～2 TO-50EC(15A) CU-18
10HP 11.4/14.4 11.4/14.5
3.5～5.5
5.5 0.5～2 TO-50EC(20A) CU-25
575~690V
3 Ø
15HP 17.9/22.7 15/19 5.5 8 0.5～2 TO-50EC(30A) CU-25
20HP 22.7/26.3 19/22 8 8 0.5～2 TO-50EC(30A) CU-35
25HP 26.3/32.3 22/27 8 8 0.5～2 TO-100S(50A) CU-35
30HP 32.3/40.6 27/34 8 8 0.5～2 TO-100S(50A) CU-50
40HP 40.6/50.2 34/42 8 8 0.5～2 TO-100S(50A) CU-50
50HP 50.2/62.1 42/52 14 8 0.5～2 TO-100S(75A) CU-65
60HP 64.5/74.1 54/62 14 14 0.5～2 TO-100S(100A) CU-80
75HP 74.1/95.6 62/80 22 14 0.5～2 TO-225S(150A) CN-100
100HP 103/118 86/99 38 22 0.5～2 TO-225S(150A) CN-125
125HP 114/149 99/125 60 38
0.5～2
TO-225S(175A) CN-150
150HP 157/175 131/147 60 60
0.5～2
TO-225S(175A) CN-150
175HP 176/194 147/163 80 60 0.5～2 TO-225S(225A) CN-300
215HP 195/253 163/212 150 80 0.5～2 TO-225S(225A) CN-300
250HP 230/258 192/216 150 150 0.5～2 TO-400S(400A) CN-300
270HP 258/294 216/246 150 150
0.5～2
TO-400S(400A) CN-300
*1: Constant torque rating.
*2: The main circuit terminals: R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, B1／P, B2,
, 
+
*3: Control line is the terminal wire on the control board.
*4: The NFB and MCB listed in the table are of TECO product numbers, products with same rated specification of
other brands may be used. To reduce electrical noise interference, ensure that a RC surge absorber (R: 10/
5W, C: 0.1f/1000VDC) is added to both sides of MCB coil.