Lenze 8400 - Page 1582

Index
1582 Lenze · 8400 HighLine · Reference manual · DMS 12.0 EN · 06/2017 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Index (C01085) 1054
Inverter motor brake
nAdd (C02293)
1125
PT1 filter time (C02294) 1125
Kp position controller (C02252) 1117
Manual entry of motor type (C02315) 1133
Max. motor speed (C02280) 1121
Moment of inertia (C02256) 1117
Motor cable cross-section (C02276) 1120
Motor cable length (C02275) 1120
Motor control (C02210) 1104
Motor cosine phi (C02240) 1114
Motor magnetising current (C02242) 1114
Motor magnetising inductance (C02241) 1114
Motor phase direction of rotation (C02272) 1119
Motor rotor resistance (C02232) 1111
Motor stator leakage inductance (C02234) 1112
Motor stator resistance (C02233) 1112
Oscillation damping filter time (C02250) 1116
Oscillation damping influence (C02249) 1116
Override point of field weakening (C02230) 1111
PLI without motion
Adaptation of ident angle (C02313)
1132
Adaptation of time duration (C02311) 1131
PLI without motion (C02312) 1132
PSM
Activate Lss sat. char. (C02307)
1131
Imax Lss saturation characteristic (C02306) 1131
Lss saturation characteristic (C02305) 1129
Maximum motor current field weakening (C02278) 1121
Rated motor current (C02237) 1113
Rated motor frequency (C02238) 1113
Rated motor power (C02231) 1111
Rated motor speed (C02236) 1112
Rated motor voltage (C02239) 1113
Reset time Imax/M controller (C02224) 1109
SC
Field feedforward control (C02261)
1118
Settings (C02229) 1110
Tdn speed controller (C02222) 1108
Tn field controller (C02228) 1110
Tn field weakening controller (C02263) 1118
Vp field controller (C02227) 1110
Vp field weakening controller (C02262) 1118
Setting of motor overload (I²xt) (C02246) 1115
Slip comp. (C02216) 1106
SLPSM
Controlled current setpoint (C02300)
1127
Filter cutoff frequency (C02302) 1128
Filter time rotor position (C02303) 1128
PLL gain (C02304) 1129
Switching speed (C02301) 1128
SLVC
Cross current controller gain (C02292)
1125
Field current controller gain (C02291) 1124
Speed limitation (C02273) 1119
Speed sensor selection (C02260) 1117
Switching frequency (C02214) 1105
Ti current controller (C02226) 1109
Ti speed controller (C02221) 1107
Ultimate motor current (C02279) 1121
VFC
Limitation V/f + sensor (C02284)
1122
Ti V/f +sensor (C02286) 1123
Time const. slip comp. (C02281) 1122
V/f base frequency (C02212) 1104
Vmin boost (C02213) 1104
Vp V/f +sensor (C02285) 1122
VFC-ECO
Minimum voltage V/f (C02289)
1124
Ti CosPhi controller (C02288) 1123
Voltage reduction ramp (C02290) 1124
Vp CosPhi controller (C02287) 1123
Vp current controller (C02225) 1109
Vp speed controller (C02220) 1107
WriteValue_1 (C01086) 1054
WriteValue_2 (C01087) 1055
WriteValue_3 (C01088) 1055
WriteValue_4 (C01089) 1055
LU: DC bus undervoltage (error message) 659
M
Machine parameters 528
Main program runtime (C00321) 872
Mains connection (behaviour) 123
Mains phase failure monitoring 308
Mains voltage (C00173) 854
Manual control 57
Manual DC-injection braking (DCB) 268
Manual entry of motor type (C01001) 1037
Manual jog 573
Setting (C01230) 1075
Manual jog to software limit position 579
Manual motor direction of rotation check 57
Master functionality (CAN) 714
MasterPin 49
Max. motor speed (C00965) 1028
Max. number of AutoFailReset processes (C00186) 857
Maximum current monitoring 308
Maximum torque (C00057) 826
Maximum torque monitoring 310
Maximum travel distance 543
MCI input words (C00876) 1019
MCI output words (C00877) 1019
MCI_InOut
Inversion (C00890)
1020
MCK 497
Accel./decel. times (C02610) 1137
Control word (C01240) 1079
Current operating mode (C01243) 1082
Current pos profile number (C01242) 1082
Current positions (C01210) 1068
Cycle (C01201) 1066
Diagnostic word (C01247) 1084