2 Parameters
2.4 BICO parameters (connectors/binectors)
SINAMICS G120 Control Units CU240B-2/CU240E-2
548 List Manual (LH11), 01/2016, A5E33839529
p2203[0...n] CO: Technology controller fixed value 3 / Tec_ctr fix val 3
p2204[0...n] CO: Technology controller fixed value 4 / Tec_ctr fix val 4
p2205[0...n] CO: Technology controller fixed value 5 / Tec_ctr fix val 5
p2206[0...n] CO: Technology controller fixed value 6 / Tec_ctr fix val 6
p2207[0...n] CO: Technology controller fixed value 7 / Tec_ctr fix val 7
p2208[0...n] CO: Technology controller fixed value 8 / Tec_ctr fix val 8
p2209[0...n] CO: Technology controller fixed value 9 / Tec_ctr fix val 9
p2210[0...n] CO: Technology controller fixed value 10 / Tec_ctr fix val 10
p2211[0...n] CO: Technology controller fixed value 11 / Tec_ctr fix val 11
p2212[0...n] CO: Technology controller fixed value 12 / Tec_ctr fix val 12
p2213[0...n] CO: Technology controller fixed value 13 / Tec_ctr fix val 13
p2214[0...n] CO: Technology controller fixed value 14 / Tec_ctr fix val 14
p2215[0...n] CO: Technology controller fixed value 15 / Tec_ctr fix val 15
r2224 CO: Technology controller fixed value effective / Tec_ctr FixVal eff
r2245 CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
r2250 CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
r2260 CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
r2262 CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
r2266 CO: Technology controller actual value after filter / Tec_ctr act aftFlt
r2272 CO: Technology controller actual value scaled / Tech_ctrl act scal
r2273 CO: Technology controller system deviation / Tec_ctrl sys_dev
p2291 CO: Technology controller maximum limiting / Tec_ctrl max_lim
p2292 CO: Technology controller minimum limiting / Tec_ctrl min_lim
r2294 CO: Technology controller output signal / Tec_ctrl outp_sig
p2295 CO: Technology controller output scaling / Tec_ctrl outp scal
r2344 CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
p2900[0...n] CO: Fixed value 1 [%] / Fixed value 1 [%]
p2901[0...n] CO: Fixed value 2 [%] / Fixed value 2 [%]
r2902[0...14] CO: Fixed values [%] / Fixed values [%]
p2930[0...n] CO: Fixed value M [Nm] / Fixed value M [Nm]
r3131 CO: Actual fault value / Act fault val
r3132 CO: Actual component number / Comp_no act
r3841 CO: Friction characteristic output / Frict outp
r8541 CO: Speed setpoint from BOP/IOP in the manual mode / N_set OP
r9712 CO: SI Motion diagnostics pos. act. val. motor side (processor 1) / SI Mtn s_act motP1
r9713[0...5] CO: SI Motion diagnostics position actual value load side / SI Mtn s_act load
r9714[0...2] CO: SI Motion diagnostics velocity (processor 1) / SI Mtn diag v P1
r9733[0...2] CO: SI Motion setpoint speed limit effective / SI Mtn setp_lim
r20095 CO: ADD 0 output Y / ADD 0 output Y
r20099 CO: ADD 1 output Y / ADD 1 output Y
r20103 CO: SUB 0 difference Y / SUB 0 difference Y
r20107 CO: SUB 1 difference Y / SUB 1 difference Y
r20111 CO: MUL 0 product Y / MUL 0 product Y
r20115 CO: MUL 1 product Y / MUL 1 product Y
r20119[0...2] CO: DIV 0 quotient / DIV 0 quotient
r20124[0...2] CO: DIV 1 quotient / DIV 1 quotient
r20129 CO: AVA 0 output Y / AVA 0 output Y
r20134 CO: AVA 1 output Y / AVA 1 output Y
r20220 CO: NSW 0 output Y / NSW 0 output Y
r20225 CO: NSW 1 output Y / NSW 1 output Y
r20231 CO: LIM 0 output Y / LIM 0 output Y
r20239 CO: LIM 1 output Y / LIM 1 output Y
r20247 CO: PT1 0 output Y / PT1 0 output Y
r20253 CO: PT1 1 output Y / PT1 1 output Y
r20261 CO: INT 0 output Y / INT 0 output Y
To Next Page
Loading...
Need help?
General