Siemens SINUMERIK 840D

Table of contents
Milling
12 Operating Manual, 03/2010, 6FC5398-7CP20-1BA0
8.3.4 Creating contour elements........................................................................................................ 332
8.3.5 Changing the contour................................................................................................................ 336
8.3.6 Contour call (CYCLE62) - only
for G code program ................................................................. 337
8.3.7 Path milling (CYCLE72)
............................................................................................................ 338
8.3.8 Contour pocket/contour s
pigot (CYCLE63/64).......................................................................... 342
8.3.9 Predrilling contour pocket (CYCLE
64)...................................................................................... 344
8.3.10 Milling contour pocket (CY
CLE63)............................................................................................ 347
8.3.11 Residual material contour
pocket (CYCLE63) .......................................................................... 349
8.3.12 Milling contour spigot (CY
CLE63)............................................................................................. 351
8.3.13 Residual material contour
spigot (CYCLE63) ........................................................................... 353
8.4 Turning - only for G c
ode programs .......................................................................................... 355
8.4.1 General...................................................................................................................................... 355
8.4.2 Stock removal (CYCLE951)...................................................................................................... 355
8.4.3 Groove (CYCLE930)................................................................................................................. 358
8.4.4 Undercut form E and F (CYCLE940)
........................................................................................ 360
8.4.5 Thread undercut (CYCLE940)
.................................................................................................. 362
8.4.6 Thread turning (CY
CLE99) ....................................................................................................... 365
8.4.7 Thread chain (CY
CLE98).......................................................................................................... 373
8.4.8 Cut-off (CYCLE92)
.................................................................................................................... 376
8.5 Contour turning - only for
G code programs ............................................................................. 378
8.5.1 General information................................................................................................................... 378
8.5.2 Representation of the cont
our................................................................................................... 379
8.5.3 Creating a new c
ontour............................................................................................................. 380
8.5.4 Creating contour element
s........................................................................................................ 382
8.5.5 Changing the contour................................................................................................................ 387
8.5.6 Contour call (CYCLE62)
............................................................................................................ 388
8.5.7 Stock removal (CYCLE952)...................................................................................................... 390
8.5.8 Stock removal residual (CY
CLE952) ........................................................................................ 394
8.5.9 Grooving (CYCLE952) .............................................................................................................. 396
8.5.10 Grooving residual material
(CYCLE952)................................................................................... 398
8.5.11 Plunge turning (CY
CLE952)...................................................................................................... 400
8.5.12 Plunge turning residual material (CYCLE
952).......................................................................... 403
8.6 Further cycles and functions ..................................................................................................... 406
8.6.1 Swiveling plane/tool (CY
CLE800)............................................................................................. 406
8.6.2 Swiveling tool (CYCLE800)....................................................................................................... 414
8.6.2.1 Swiveling tool/preloading milling tools - only for G
code program (CYCLE800)....................... 414
8.6.2.2 Swiveling tool/orienting milling tools - o
nly for G code program (CYCLE800).......................... 415
8.6.3 High-speed settings (CYCLE832)............................................................................................. 416
8.6.4 Subroutines ............................................................................................................................... 418
8.7 Further cycles and functions ShopMill ...................................................................................... 420
8.7.1 Transformations ........................................................................................................................ 420
8.7.2 Translation................................................................................................................................. 421
8.7.3 Rotation..................................................................................................................................... 422
8.7.4 Scaling....................................................................................................................................... 423
8.7.5 Mirroring .................................................................................................................................... 424
8.7.6 Straight or circular machining.................................................................................................... 425
8.7.7 Programming a straight line ...................................................................................................... 427
8.7.8 Programming a circle with known center point ......................................................................... 428
8.7.9 Programming a circle with known radius .................................................................................. 429
8.7.10 Helix .......................................................................................................................................... 430
8.7.11 Polar coordinates ...................................................................................................................... 431
8.7.12 Straight polar............................................................................................................................. 432
8.7.13 Circle polar ................................................................................................................................ 433