EasyManua.ls Logo

Danfoss VLT series - Page 13

Danfoss VLT series
390 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
7.14 CAM Mode Objects
288
7.14.1 Parameter: CAM Prole Memory Layout (0x380F) 288
7.14.2 Parameter: CAM Status (0x3801) 289
7.14.3 Parameter: CAM Control (0x3800) 290
7.14.4 Parameters: CAM Prole 1–8 (0x3810–0x3817) 291
7.14.5 Parameters: CAM Data 1–8 (0x3820–3827) 301
7.14.6 Parameters: CAM Pattern 1–8 (0x3830–3837) 301
7.14.7 Parameter: CAM Prole Selector (0x3804) 302
7.14.8 Parameter: CAM Prole Status (0x3805) 303
7.14.9 Parameter: CAM Slave Oset (0x3807) 304
7.14.10 Parameter: CAM Slave Scaling (0x3809) 305
7.14.11 Parameter: Minimum Blending Distance (0x380A) 306
7.14.12 Parameter: Logical CAM Position (0x2020) 307
7.14.13 Parameter: Logical CAM Set Point (0x2021) 307
7.14.14 Parameter: Active Segment ID (0x2019) 307
7.14.15 Parameter: Last Node ID (0x201A) 308
7.14.16 Parameter: Logged Values (0x3870) 308
7.14.17 Parameter: Digital Input Counters (0x3860) 309
7.15 Gear Mode Objects
309
7.15.1 Parameter: Gear Ratio (0x3900) 309
7.15.2 Parameter: Gear Synchronization Option Code (0x3901) 310
7.15.3 Parameter: Gear Master Start Distance (0x3902) 311
7.15.4 Parameter: Gear Master Sync Position (0x3903) 312
7.15.5 Parameter: Gear Slave Sync Position (0x3904) 312
7.16 ISD Inertia Measurement Objects
313
7.16.1 Parameter 52-60: Measured Inertia (0x2009) 313
7.16.2 Parameters 52-61 and 52-62: Inertia Measurement Parameters (0x200A) 314
7.17 Digital CAM Switch Objects
314
7.17.1 Parameter: On Compensation (0x3840) 314
7.17.2 Parameter: O Compensation (0x3841) 315
7.17.3 Parameter: Hysteresis (0x3842) 315
7.17.4 Parameters: Digital CAM Switch Parsing Control (0x3843) 316
7.17.5 Parameter: Digital CAM Switches Data (0x3844) 318
7.18 Touch Probe Objects
318
7.18.1 Parameter: Touch Probe Function (0x60B8) 318
7.18.2 Parameter: Touch Probe Status (0x60B9) 319
7.18.3 Parameter 51-51: Touch Probe 1 Positive Edge (0x60BA) 320
7.18.4 Parameter 51-54: Touch Probe 1 Negative Edge (0x60BB) 321
7.18.5 Parameter 51-61: Touch Probe 2 Positive Edge (0x60BC) 321
7.18.6 Parameter 51-64: Touch Probe 2 Negative Edge (0x60BD) 321
Contents Programming Guide
MG36D102 Danfoss A/S © 01/2017 All rights reserved. 11

Table of Contents

Other manuals for Danfoss VLT series

Related product manuals