Gemalto CINTERION BGS2T - 14.4 AT^SCID SIM Identification Number

To Next Page

To Previous Page

BGS2T AT Command Set

14.4 AT^SCID

BGS2T_ATC_V01.301 Page 411 of 554 1/31/12

14.4 AT^SCID SIM Identification Number

AT^SCID serves to query the SIM identification number. This information is retrieved from SIM elementary file

ICCID

; for details refer to 3GPP TS 11.11 [14].

Syntax

Parameter Description

SIM identification number.

Test Command

AT^SCID=?

Response(s)

Exec Command

AT^SCID

Response(s)

^SCID: <cid>

ERROR

+CME ERROR: <err>

PIN ASC0 MUX1 MUX2 MUX3  Last

- + + + + - -

<cid>

(str)

Confidential / Released

Main Page

Default Chapter3
- Table of Contents3
1 Introduction14
- Scope of the Document14
- Table 1.1: Applicability of at Commands and Features14
- Related Documents15
- Document Conventions17
- AT Command Syntax19
- Communication between Customer Application and BGS2T21
- Supported Character Sets22
- Unsolicited Result Code Presentation28
  - Common Urcs29
- Errors and Messages30
- Serial Interface Flow Control31
  - Software Flow Control (XON/OFF Handshake)31
  - Hardware Flow Control (RTS/CTS Handshake)31
- Common PCN Handset Specification (CPHS)32
2 Configuration Commands33
- AT&F Reset at Command Settings to Factory Default Values33
- AT&V Display Current Configuration34
- AT&W Store at Command Settings to User Defined Profile37
- ATQ Result Code Presentation Mode38
- ATV Result Code Format Mode39
  - Verbose and Numeric Result Codes39
- ATX CONNECT Result Code Format40
- ATZ Restore at Command Settings from User Defined Profile41
- AT+CFUN Functionality Level42
  - Wake up the ME from SLEEP Mode44
  - Table 2.3: Wakeup Events in NON-CYCLIC and CYCLIC SLEEP Modes45
- AT^SMSO Switch off BGS2T46
- AT+GCAP Capabilities List47
- AT+CMEE Error Message Format48
- AT+CSCS Character Set53
- AT^SCFG Extended Configuration Settings54
- AT^SM20 Set M20 Compatibility Mode63
3 Status Control Commands64
- AT+CMER Common Event Reporting Configuration64
- AT+CIND Indicator Control66
- AT^SIND Extended Indicator Control69
- AT+CEER Extended Error Report76
- ATS18 Extended Call Release Report90
- AT+CPAS Activity Status92
- AT+WS46 Select Wireless Network93
4 Serial Interface Control Commands94
- AT\Q Flow Control94
- AT&C Set Data Carrier Detect (DCD) Line Mode95
- AT&D Set Data Terminal Ready (DTR) Line Mode96
- AT&S Set Data Set Ready (DSR) Line Mode97
- ATE at Command Echo98
- AT+ILRR Bit Rate Reporting99
- AT+IPR Bit Rate101
  - Autobauding102
- AT+CMUX Multiplex Mode104
- AT+ICF Character Framing107
- AT^STPB Transmit Parity Bit (for 7E1 and 7O1 Only)109
5 Security Commands110
- AT+CPIN PIN Authentication110
  - What to Do if PIN or Password Authentication Fails112
- AT+CPIN2 PIN2 Authentication114
- AT^SPIC Display PIN Counter116
- AT+CLCK Facility Lock120
- AT^SLCK Facility Lock125
- AT+CPWD Change Password126
- AT^SPWD Change Password130
6 Identification Commands131
- ATI Display Product Identification Information131
- AT+CGMI Request Manufacturer Identification132
- AT+GMI Request Manufacturer Identification132
- AT+CGMM Request Model Identification133
- AT+GMM Request Model Identification133
- AT+CGMR Request Revision Identification of Software Status134
- AT+GMR Request Revision Identification of Software Status134
- AT+CGSN Request International Mobile Equipment Identity (IMEI)135
- AT+GSN Request International Mobile Equipment Identity (IMEI)135
- AT+CIMI Request International Mobile Subscriber Identity (IMSI)136
7 Call Related Commands137
- Call Status Information137
- ATA Connect to Incoming Call138
- ATD Mobile Originated Call to Specified Number139
- Atd><Mem><N> Mobile Originated Call Using Specific Memory and Index Number141
- Atd><N> Mobile Originated Call from Active Memory Using Index Number143
- Atd><Str> Mobile Originated Call from Active Memory Using Corresponding Field144
- ATDI Mobile Originated Data Call to ISDN Number146
- ATDL Redial Last Number Used147
- ATH Disconnect Existing Connection148
- AT+CHUP Hang up Call149
- AT^SHUP Hang up Call(S) Indicating a Specific 3GPP TS 24.008 Release Cause150
- ATS0 Set Number of Rings before Automatically Answering a Call151
- ATS6 Set Pause before Blind Dialing152
- ATS7 Set Number of Seconds to Wait for Connection Completion153
- ATS8 Comma Dial Pause Time154
- ATS10 Set Disconnect Delay after Indicating the Absence of Data Carrier155
- ATO Switch from Command Mode to Data Mode / PPP Online Mode156
- Escape from Data Mode to at Command Mode157
- AT+CBST Select Bearer Service Type158
- AT+CRLP Configure RLP Parameters for Outgoing Non-Transparent Data Calls159
- AT+CLCC List of Current Calls160
- AT^SLCC Extended List of Current Calls162
- AT+CR Service Reporting Control167
- AT+CRC Incoming Call Indication Format168
- AT+CSNS Single Numbering Scheme170
- AT^SCNI List Call Number Information171
- AT^SLCD Display Last Call Duration172
- AT^STCD Display Total Call Duration173
- ATP Select Pulse Dialing174
- ATT Select Tone Dialing174
- ATS2 Set Escape Sequence Character175
8 Network Service Commands176
- AT+COPN Read Operator Names176
- AT+COPS Operator Selection177
- AT^SOPS Extended Operator Selection180
- AT^SRPN Replace Operator Names182
- AT+CREG Network Registration Status184
- AT+CSQ Signal Quality187
- AT^SMONC Cell Monitoring188
- AT^SMOND Cell Monitoring190
- AT^MONI Monitor Idle Mode and Dedicated Mode193
  - AT^MONI Responses194
  - Service States195
- AT^MONP Monitor Neighbor Cells196
  - AT^MONP Responses197
- AT^SMONG Packet Data Monitor198
  - AT^SMONG Cell Info Table199
- AT^SALS Alternate Line Service200
- AT^SHOM Display Homezone202
- AT^SPLM Read the PLMN List203
- AT+CPOL Preferred Operator List204
- AT^SPLR Read Entry from the Preferred Operators List205
- AT^SPLW Write an Entry to the Preferred Operators List206
- AT^SPCL Set Preferred Cell List207
- AT^SNMON Network Monitoring209
9 Supplementary Service Commands211
- AT+CACM Accumulated Call Meter (ACM) Reset or Query211
- AT^SACM Advice of Charge and Query of ACM and Acmmax212
- AT+CAMM Accumulated Call Meter Maximum (Acmmax) Set or Query214
- AT+CAOC Advice of Charge Information215
- AT+CCUG Closed User Group216
- AT+CCFC Call Forwarding Number and Conditions Control218
- AT+CCWA Call Waiting222
- AT+CHLD Call Hold and Multiparty226
- AT+CLIP Calling Line Identification Presentation228
- AT+CLIR Calling Line Identification Restriction230
- AT+COLP Connected Line Identification Presentation231
- AT+CPUC Price Per Unit and Currency Table233
- AT+CSSN Supplementary Service Notifications235
- AT+CUSD Unstructured Supplementary Service Data237
10 Internet Service Commands239
- AT^SICS Internet Connection Setup Profile242
- AT^SICI Internet Connection Information246
  - Checking Connection Profile Status247
- AT^SIPS Internet Profile Storage249
- AT^SISS Internet Service Setup Profile251
- Table 10.2: Applicability of AT^SISS <Srvparmtag> Values251
- AT^SISI Internet Service Information261
- AT^SISO Internet Service Open263
  - Example: Accepting / Rejecting Socket Connection Request from Remote Client267
- AT^SISC Internet Service Close269
- AT^SISR Internet Service Read Data270
  - Example: Socket Host Reads Small Amounts of UDP Data Packets (URC Mode)271
- AT^SISW Internet Service Write Data273
  - Usage of Parameter <Eodflag275
- AT^SIST Enter Transparent Access Mode276
- AT^SISE Internet Service Error Report278
- Internet Service URC "^SIS279
- Examples of How to Configure and Use Internet Service Profiles283
11 Packet Domain Related Commands297
- AT+CGACT PDP Context Activate or Deactivate297
- AT+CGANS Manual Response to a Network Request for PDP Context Activation299
- AT+CGATT GPRS Attach or Detach301
- AT+CGAUTO Automatic Response to a Network Request for PDP Context Activation302
- AT+CGDATA Enter Data State304
  - Automatic Deactivation of PDP Context During Dial-Up PPP305
- AT+CGDCONT Define PDP Context306
- AT+CGEQMIN Rel. 99 Quality of Service Profile (Minimum Acceptable)308
- AT+CGEQREQ Rel. 99 Quality of Service Profile (Requested)312
- AT+CGEREP GPRS Event Reporting316
- AT+CGPADDR Show PDP Address318
- AT+CGQMIN Quality of Service Profile (Minimum Acceptable)319
- AT+CGQREQ Quality of Service Profile (Requested)323
- AT+CGREG GPRS Network Registration Status326
- AT+CGSMS Select Service for MO SMS Messages328
- AT^SGAUTH Set Type of Authentication for PPP Connection329
- AT^SGCONF Configuration of GPRS Related Parameters330
- ATA Manual Acceptance of a Network Request for PDP Context Activation331
- ATD*99# Request GPRS Service332
- ATD*98# Request GPRS IP Service333
- ATH Manual Rejection of a Network Request for PDP Context Activation334
- ATS0 Automatic Response to Network Request for PDP Context Activation335
- Using GPRS at Commands (Examples)336
- Using the GPRS Dial Command ATD338
12 FAX Commands339
- FAX Parameters339
  - Summary of Fax Class 2 Urcs Defined by EIA PN-2388341
  - Table 12.1: Summary of Fax Class 2 Urcs Defined by EIA PN-2388341
- AT+FBADLIN Bad Line Threshold342
- AT+FBADMUL Error Threshold Multiplier343
- AT+FBOR Query Data Bit Order344
- AT+FCIG Query or Set the Local Polling ID345
- AT+FCLASS Fax: Select, Read or Test Service Class346
- AT+FCQ Copy Quality Checking347
- AT+FCR Capability to Receive348
- AT+FDCC Query or Set Capabilities349
- AT+FDFFC Data Compression Format Conversion350
- AT+FDIS Query or Set Session Parameters351
- AT+FDR Begin or Continue Phase C Data Reception352
- AT+FDT Data Transmission353
- AT+FET End a Page or Document354
- AT+FK Kill Operation, Orderly FAX Abort355
- AT+FLID Query or Set the Local ID Setting Capabilities356
- AT+FMDL Identify Product Model357
- AT+FMFR Request Manufacturer Identification358
- AT+FOPT Set Bit Order Independently359
- AT+FPHCTO DTE Phase C Response Timeout360
- AT+FREV Identify Product Revision361
- AT+FRH Receive Data Using HDLC Framing362
- AT+FRM Receive Data363
- AT+FRS Receive Silence364
- AT+FTH Transmit Data Using HDLC Framing365
- AT+FTM Transmit Data366
- AT+FTS Stop Transmission and Wait367
- AT+FVRFC Vertical Resolution Format Conversion368
13 Short Message Service (SMS) Commands369
- SMS Parameters369
- AT+CMGC Send SMS Command373
- AT+CMGD Delete Short Message374
  - AT+CMGF Select SMS Message Format375
- AT+CMGL List SMS Messages from Preferred Store376
- AT+CMGR Read SMS Messages378
- AT+CMGS Send SMS380
- AT+CMGW Write Short Messages to Memory382
- AT+CMSS Send Short Messages from Storage384
- AT+CNMA New Message Acknowledgement to ME/TE385
- AT+CNMI SMS Event Reporting Configuration386
- AT+CPMS Preferred SMS Message Storage389
- AT+CSCA SMS Service Center Address391
- AT+CSCB Select Cell Broadcast Message Indication392
- AT+CSDH Show SMS Text Mode Parameters393
- AT+CSMP Set SMS Text Mode Parameters394
- AT+CSMS Select Message Service396
- AT^SLMS List SMS Memory Storage398
- AT^SMGL List Short Messages from Preferred Store Without Setting Status to REC READ399
- AT^SMGO Set or Query SMS Overflow Presentation Mode or Query SMS Overflow400
- AT^SMGR Read Short Message Without Setting Status to REC READ402
- AT^SSCONF SMS Command Configuration403
- AT^SSDA Set SMS Display Availability404
- AT^SSMSS Set Short Message Storage Sequence405
14 SIM Related Commands406
- AT+CRSM Restricted SIM Access406
- AT+CSIM Generic SIM Access408
- AT+CXXCID Display Card ID410
- AT^SCID SIM Identification Number411
- AT^SCKS Query SIM and Chip Card Holder Status412
- AT^SSET SIM Data Ready Indication414
- AT^SXSM Extended SIM Access415
15 SIM Application Toolkit (SAT) Commands417
- Usage of Remote-SAT419
  - Automatic Response Mode (AR Mode)419
  - Explicit Response Mode (er Mode)419
  - Character Sets419
  - SIM Update Initiated by the Network419
  - Icon Handling420
  - Remote-SAT States421
  - Remote-SAT State Transition Diagram422
  - Remote-SAT State Transition Table423
  - Table 15.1: State: RESET Description423
  - Table 15.2: State: off Description423
  - Table 15.3: State: IDLE Description423
  - Table 15.4: State: PAC Description424
  - Table 15.5: State: WAIT Description424
- Remote-SAT Command Types425
- Table 15.6: Command Type Table425
- AT^SSTA Remote-SAT Interface Activation426
- SSTN SAT Notification428
- AT^SSTGI SAT Get Information430
- AT^SSTGI SAT Get Information - Refresh (1)431
- AT^SSTGI SAT Get Information - Set up Event List (5)433
- AT^SSTGI SAT Get Information - Set up Call (16)434
- AT^SSTGI SAT Get Information - Send SS (17)436
- AT^SSTGI SAT Get Information - Send USSD (18)437
- AT^SSTGI SAT Get Information - Send Short Message (19)438
- AT^SSTGI SAT Get Information - Send DTMF (20)439
- AT^SSTGI SAT Get Information - Launch Browser (21)440
- AT^SSTGI SAT Get Information - Play Tone (32)442
- AT^SSTGI SAT Get Information - Display Text (33)444
- AT^SSTGI SAT Get Information - Get Inkey (34)446
- AT^SSTGI SAT Get Information - Get Input (35)448
- AT^SSTGI SAT Get Information - Select Item (36)450
- AT^SSTGI SAT Get Information - Set up Menu (37)452
- AT^SSTGI SAT Get Information - Set up Idle Mode Text (40)454
- AT^SSTGI SAT Get Information - Language Notification (53)455
- AT^SSTR SAT Response456
- AT^SSTR SAT Response - Refresh (1)458
- AT^SSTR SAT Response - Set up Event List (5)459
- AT^SSTR SAT Response - Set up Call (16)460
- AT^SSTR SAT Response - Send SS (17)461
- AT^SSTR SAT Response - Send USSD (18)462
- AT^SSTR SAT Response - Send Short Message (19)463
- AT^SSTR SAT Response - Send DTMF (20)464
- AT^SSTR SAT Response - Launch Browser (21)465
- AT^SSTR SAT Response - Play Tone (32)466
- AT^SSTR SAT Response - Display Text (33)467
- AT^SSTR SAT Response - Get Inkey (34)468
- AT^SSTR SAT Response - Get Input (35)470
- AT^SSTR SAT Response - Select Item (36)472
- AT^SSTR SAT Response - Setup Menu (37)473
- AT^SSTR SAT Response - Set up Idle Mode Text (40)474
- AT^SSTR SAT Response - Language Notification (53)475
- AT^SSTR SAT Event - Menu Selection (211)476
- AT^SSTR SAT Event - User Activity (232)477
- AT^SSTR SAT Event - Idle Screen Available (233)478
- AT^SSTR SAT Event - Language Selection (235)479
- AT^SSTR SAT Event - Browser Termination (236)480
- AT^SSTR SAT Event - Terminate Command (254)481
- Examples for Using Remote-SAT482
16 Phonebook Commands485
- Sort Order for Phonebooks485
- AT+CPBR Read from Phonebook486
- AT+CPBS Select Phonebook Memory Storage489
- AT+CPBW Write into Phonebook491
- AT^SPBC Find First Matching Entry in Sorted Phonebook494
- AT^SPBD Purge Phonebook Memory Storage495
- AT^SPBG Display Phonebook Entries in Alphabetical Order496
- AT^SPBS Step through the Selected Phonebook Alphabetically499
- AT+CNUM Read Own Numbers503
- AT^SDLD Delete the 'Last Number Redial' Memory504
17 Hardware Related Commands505
- AT+CCLK Real Time Clock505
- AT+CALA Alarm Configuration506
- AT^SBV Battery/Supply Voltage509
- AT^SSYNC Configure SYNC Pin510
  - ME Status Indicated by Status LED Patterns510
  - Table 17.1: Modes of the LED and Indicated ME Functions511
- AT^SCTM Critical Operating Temperature Monitoring512
  - Deferred Shutdown513
18 Miscellaneous Commands515
- A/ Repeat Previous Command Line515
- ATS3 Command Line Termination516
- ATS4 Response Formatting517
- ATS5 Command Line Editing518
- AT^SFDL Firmware Download519
19 Appendix520
- Restricted Access to SIM Data after SIM PIN Authentication520
- Star-Hash (*#) Network Commands521
- Table 19.1: Star-Hash (*#) Command Overview521
- Table 19.2: Abbreviations of Codes and Parameters Used in Table522
- Table 19.3: Star-Hash Command Response Parameters523
- Table 19.4: Star-Hash Commands for Supplementary Services523
- Available at Commands and Dependency on SIM PIN524
- Table 19.5: Available at Commands and Dependency on SIM PIN524
- Availability of at Commands Depending on Operating Mode of ME532
- Table 19.6: Availability of at Commands Depending on Operating Mode of ME532
- AT Command Settings Storable with AT&W540
- Table 19.7: Settings Stored to User Profile on ASC0 / MUX Channel 1540
- Table 19.8: Settings Stored to User Profile on MUX Channels 2 and 3541
- Factory Default Settings Restorable with AT&F543
- Table 19.9: Factory Default Settings Restorable with AT&F543
- Summary of Unsolicited Result Codes (URC)545
- Table 19.10: Summary of Unsolicited Result Codes (URC)545
- Alphabetical List of at Commands548
- Table 19.11: Alphabetical List of at Commands548

Gemalto CINTERION BGS2T - 14.4 AT^SCID SIM Identification Number

Table of Contents

Related product manuals