Command and Drive Data Sets – Overview
Parameters
1-303
© Siemens AG 2007 All Rights Reserved
SINAMICS G120 Control Units CU240S, Edition 05/2007
p1132[0...2] Ramp-down initial rounding time / Ramp-dwn ini. Trnd
p1133[0...2] Ramp-down final rounding time / Ramp-dwn fin. Trnd
p1134[0...2] Rounding type / Rounding type
p1135[0...2] OFF3 ramp-down time / OFF3 ramp-dwn time
p1202[0...2] Motor-current: Flying start / Mot. cur: Flystart
p1203[0...2] Search rate: Flying start / SrchRate: Flystart
p1227[0...2] Zero speed detection monitoring time / Zero speed time
p1232[0...2] DC braking current / DC braking current
p1233[0...2] Duration of DC braking / DC brak. duration
p1234[0...2] DC braking start frequency / DC brk. start freq
p1236[0...2] Compound braking current / Compound brk. cur.
p1240[0...2] Configuration of Vdc controller / Vdc controller
p1243[0...2] Dynamic factor of Vdc-max / Vdc-max dyn. fact.
p1245[0...2] Switch on level kin. buffering / KIB ON level
r1246[0...2] CO: Switch-on level kin buffering / KIB ON level
p1247[0...2] Dyn. factor of kinetic buffering / Dyn. factor of KIB
p1250[0...2] Gain of Vdc-controller / Gain of Vdc ctrl.
p1251[0...2] Integration time Vdc-controller / Int. time Vdc ctrl
p1252[0...2] Differential time Vdc-controller / Diff.time Vdc ctrl
p1253[0...2] Vdc-controller output limitation / Vdc ctrl outp. lim
p1256[0...2] Reaction of kinetic buffering / Reaction of KIB
p1257[0...2] Freq limit for kinetic buffering / Freq limit for KIB
p1300[0...2] Control mode / Control mode
p1300[0...2] Control mode / Control mode
p1310[0...2] Continuous boost / Continuous boost
p1311[0...2] Acceleration boost / Acceleration boost
p1312[0...2] Starting boost / Starting boost
p1316[0...2] Boost end frequency / Boost end freq.
p1320[0...2] Programmable V/f freq. coord. 1 / V/f freq. coord. 1
p1321[0...2] Programmable V/f volt. coord. 1 / V/f volt. coord. 1
p1322[0...2] Programmable V/f freq. coord. 2 / V/f freq. coord. 2
p1323[0...2] Programmable V/f volt. coord. 2 / V/f volt. coord. 2
p1324[0...2] Programmable V/f freq. coord. 3 / V/f freq. coord. 3
p1325[0...2] Programmable V/f volt. coord. 3 / V/f volt. coord. 3
p1333[0...2] Start frequency for FCC / Start freq for FCC
p1334[0...2] Slip compensation activation range / Slip c. act. range
p1335[0...2] Slip compensation / Slip compensation
p1336[0...2] Slip limit / Slip limit
p1338[0...2] Resonance damping gain V/f / Res.damp. gain V/f
p1340[0...2] Imax controller prop. gain / Imax ctrl prp gain
p1341[0...2] Imax controller integral time / Imax ctrl int time
p1345[0...2] Imax voltage ctrl. prop. gain / Imax volt prp gain
p1346[0...2] Imax voltage ctrl. integral time / Imax volt int time
p1350[0...2] Voltage soft start / Voltage soft start
p1400[0...2] Configuration of speed control / Config. of n-ctrl.
p1442[0...2] Filter time for act. speed / Filter time n_act.
p1452[0...2] Filter time for act.speed (SLVC) / Act.spd.filt. SLVC
p1460[0...2] Gain speed controller / Gain of n-ctrl.
p1462[0...2] Integral time speed controller / Tn of n-ctrl.
p1470[0...2] Gain speed controller (SLVC) / Gain n-ctrl (SLVC)
p1472[0...2] Integral time n-ctrl. (SLVC) / Tn of n-ctrl. SLVC
p1488[0...2] Droop input source / Droop input source
p1489[0...2] Droop scaling / Droop scaling
p1496[0...2] Scaling accel. precontrol / Scal acc. prectrl.
p1499[0...2] Scaling accel. torque control / Scal acc. trq ctrl
To Next Page
Loading...
